| Control Unit |
SPN |
FMI |
Pri. |
Description |
| C03 |
63 |
09 |
3 |
CAN Bus message missing from control unit E13 (VCM) - feed rate.
First check diagnostic address C03 133 and switch off the feed rate option if the latter is not installed. |
| C03 |
96 |
09 |
3 |
CAN Bus message missing from right control unit - fuel level. |
| C03 |
110 |
09 |
3 |
CAN Bus message missing from engine control unit - coolant temperature. |
| C03 |
190 |
09 |
3 |
CAN Bus message missing from engine control unit - engine speed. |
| C03 |
627 |
03 |
3 |
Delayed power supply (circuit 006) › voltage is too high (greater than 16 VDC). |
| C03 |
628 |
12 |
1 |
Controller cannot exit boot block program. Disconnect cornerpost control unit connector X500. Reconnect connector. Replace cornerpost control unit if condition persists. |
| C03 |
630 |
11 |
1 |
EEPROM failed test at power up. Replace cornerpost control unit if condition persists. |
| C03 |
639 |
19 |
3 |
CAN Bus messages are not being transmitted or received correctly. Possible effects are none, slow response, or machine down. |
| C03 |
1079 |
03 |
3 |
Concave position sensor supply voltage too high - greater than 5.5 VDC. |
| C03 |
1079 |
04 |
3 |
Concave position sensor supply voltage too low - less than 4.5 VDC. |
| C03 |
1486 |
03 |
3 |
Concave position sensor voltage too high - greater than 4.5 VDC. Faulty sensor or wiring. |
| C03 |
1486 |
04 |
3 |
Concave position sensor voltage too low - less than 0.5 VDC. Faulty sensor or wiring. |
| C03 |
1487 |
03 |
3 |
Dimmer voltage is too high - greater than 4.5 VDC. Faulty device or wiring. |
| C03 |
1487 |
04 |
3 |
Dimmer voltage is too low - less than 0.5 VDC. Faulty device or wiring. |
| C03 |
1492 |
08 |
3 |
Cab interior backlighting output transistor detects an open, short, over voltage, or over temperature condition. The cornerpost control unit will turn off the backlighting. The fault condition must be removed before the backlighting can be turned on. |
| C03 |
1493 |
09 |
3 |
CAN Bus message missing from master tailings sensor - tailings volume. |
| C03 |
1500 |
11 |
3 |
A switch on cornerpost display unit 1 is closed for longer than 30 seconds. |
| C03 |
1501 |
11 |
3 |
A switch on cornerpost display unit 2 is closed for longer than 30 seconds. |
| C03 |
1502 |
11 |
3 |
A switch on cornerpost display unit 3 is closed for longer than 30 seconds. |
| C03 |
1503 |
09 |
3 |
CAN Bus message missing from armrest control unit - armrest switch status. |
| C03 |
1510 |
09 |
3 |
CAN Bus message missing from right control unit - temperatures on combine. |
| C03 |
1511 |
09 |
3
l |
CAN Bus message missing from right control unit - grain loss. |
| C03 |
1515 |
09 |
3 |
CAN Bus message missing from header control unit - header data. |
| C03 |
1552 |
03 |
3 |
CLIMATRAK temperature setpoint adjust voltage too high - greater than 4.5 V DC. Faulty device or wiring. |
| C03 |
1552 |
04 |
3 |
CLIMATRAK temperature setpoint adjust voltage too low - less than 0.5 V DC. Faulty device or wiring. |
| C03 |
1552 |
13 |
3 |
CLIMATRAK temperature setpoint adjust not calibrated. |
| C03 |
1553 |
03 |
3 |
CLIMATRAK fan speed adjust voltage too high - greater than 4.5 V DC. Faulty device or wiring. |
| C03 |
1553 |
04 |
3 |
CLIMATRAK fan speed adjust voltage too low - less than 0.5 V DC. Faulty device or wiring. |
| C03 |
1553 |
13 |
3 |
CLIMATRAK fan speed adjust not calibrated. |
| C03 |
1565 |
09 |
3 |
CAN Bus message missing from armrest control unit - separator and header engage status. |