| SPF - SPFH Main Control Unit Diagnostic Trouble Codes |
| Control Unit |
SPN |
FMI |
Pri. |
Indicator Light |
Description |
Effect |
| SPF |
628 |
12 |
2 |
|
Program Memory Failure. |
Control unit functions not available. |
| SPF |
630 |
12 |
|
|
No Factory / Dealer Settings. |
Initial calibration cannot be called back with the reset switch. |
| SPF |
1508 |
00 |
2 |
Hydraulic oil temperature |
Hydraulic Oil Temperature (Reservoir) High - Up to SN 508099. |
Hot hydraulic oil can be the cause of damage in the hydraulic system. |
| SPF |
1563 |
12 |
2 |
|
Incompatible Control Unit. |
No control unit function is available. |
| SPF |
1713 |
00 |
2 |
Hydraulic oil filter |
Hydraulic Oil Filter Restriction Switch. |
Reduced filter performance, unfiltered oil can be the cause of damage in the hydraulic system. |
| SPF |
300000 |
14 |
2 |
Stationary knife adjust |
False Knock Detected Before Stationary Knife Adjust. |
Stationary knife adjust process aborted. |
| SPF |
300002 |
14 |
2 |
Stationary knife adjust |
Left Stationary Knife Motor Failure. |
Motor failure during stationary knife away process. |
| SPF |
300003 |
14 |
2 |
Stationary knife adjust |
Right Stationary Knife Motor Failure. |
Motor failure during stationary knife away process. |
| SPF |
300004 |
09 |
|
Stationary knife adjust |
Left Stationary Knife Motor Sensor Failure. |
Stationary knife adjust process will continue to set the left stationary knife clearance based on time calculation. |
| SPF |
300005 |
09 |
|
Stationary knife adjust |
Right Stationary Knife Motor Sensor Failure. |
Stationary knife adjust process will continue to set the right stationary knife clearance based on time calculation. |
| SPF |
300006 |
14 |
3 |
|
Seat Switch Not Closed. |
|
| SPF |
300007 |
14 |
2 |
Knife sharpening |
Manual Reverse At Start Up. |
Manual reverse at start up. |
| SPF |
300008 |
14 |
3 |
Cutterhead speed |
Wait For Cutterhead Spin Down. |
Wait for cutterhead spin down. |
| SPF |
300009 |
14 |
2 |
Depends on required Powr-Savr function |
Powr-Savr Function Denied, No Powr-Savr Motor Power. |
No Powr-Savr motor power, Powr-Savr function can not be performed. |
| SPF |
300011 |
14 |
3 |
Depends on required Powr-Savr function |
Four Speed LOC Not in Neutral. |
Requested Powr-Savr function can not be performed. |
| SPF |
300012 |
14 |
|
Stationary knife adjust |
Intermittent Knocking After Knocks Disappear. |
Stationary knife adjustment stops intermediately. |
| SPF |
300013 |
14 |
|
Stationary knife adjust |
Knock During Stationary Knife Tension Release. |
|
| SPF - SPFH Main Control Unit Diagnostic Trouble Codes |
| Control Unit |
SPN |
FMI |
Pri. |
Indicator Light |
Description |
Effect |
| SPF |
300014 |
14 |
3 |
Depends on required Powr-Savr function |
Powr-Savr Request Denied, Main Clutch On. |
Requested Powr-Savr function can not be performed. |
| SPF |
300015 |
14 |
3 |
Kernel processor adjust |
Kernel Processor Clearance Adjust Request Denied, Main Clutch Not On. |
Kernel processor adjust function can not be performed. |
| SPF |
300016 |
14 |
3 |
Stationary knife adjust |
Stationary Knife Adjust Request Denied, Sound Sending Units Failed. |
Requested Powr-Savr function can not be performed. |
| SPF |
300017 |
14 |
2 |
Depends on required Powr-Savr function |
Powr-Savr Request Denied, Quick Stop Pressed. |
|
| SPF |
300018 |
00 |
3 |
Depends on required Powr-Savr function |
Powr-Savr Request Denied, Cutterhead Speed Too High. |
Requested Powr-Savr function can not be performed. |
| SPF |
300018 |
01 |
3 |
Depends on required Powr-Savr function |
Powr-Savr Request Denied, Engine Speed Too Low-Four Speed LOC Only. |
Requested Powr-Savr function can not be performed. |
| SPF |
300019 |
00 |
3 |
Depends on required Powr-Savr function |
Powr-Savr Request Denied, Engine Speed Too High-Four Speed LOC Only. |
Requested Powr-Savr function can not be performed. |
| SPF |
300019 |
01 |
3 |
Depends on required Powr-Savr function |
Powr-Savr Request Denied, Cutterhead Speed Too Low. |
Requested Powr-Savr function can not be performed. |
| SPF |
300020 |
14 |
3 |
|
Main Clutch Denied, Interlock Active. |
Main clutch is disabled. |
| SPF |
300021 |
14 |
3 |
|
Main Clutch Denied, Engine Speed Out Of Range. |
Main clutch can not be engaged, diagnostic trouble code disappears when the rpm-condition disappears. |
| SPF |
300022 |
14 |
3 |
|
Main Clutch Denied, Sharpening Door Potentiometer Failure or Open. |
Sharpening door open or sharpening door potentiometer failure. |
| SPF |
300023 |
14 |
3 |
|
Main Clutch Denied, Street Mode Active. |
Main clutch is disabled. |
| SPF |
300024 |
14 |
3 |
|
Main Clutch Denied, Kernel Processor Belt Not Tensioned. |
Main clutch can not be engaged. |
| SPF |
300025 |
14 |
3 |
|
Main Clutch Denied, Operator Seat Switch Not Closed. |
Main clutch is disabled, diagnostic trouble code disappears when main clutch is switched off. |
| SPF |
300026 |
14 |
3 |
|
Turn Signals On. |
|
| SPF |
300027 |
14 |
|
|
Kernel Processor Option Not Available. |
|
| SPF - SPFH Main Control Unit Diagnostic Trouble Codes |
| Control Unit |
SPN |
FMI |
Pri. |
Indicator Light |
Description |
Effect |
| SPF |
300029 |
14 |
2 |
Automatic lubrication system |
Automatic Lubrication Failed. |
|
| SPF |
300030 |
02 |
2 |
Length of cut |
Feed Roll Speed Sensor Failed. |
|
| SPF |
300031 |
14 |
3 |
Depends on required Powr-Savr function |
Powr-Savr Denied, Field Mode Not Active. |
Requested Powr-Savr function can not be performed. |
| SPF |
300032 |
14 |
2 |
|
Third Gear Switch Failure, Transmission Overspeed. |
Throttle down the engine speed to 1650 rpm. |
| SPF |
300034 |
01 |
2 |
Length of cut |
IVLOC Load Pressure Low. |
Feed roll forward operation is disabled after additional 9 seconds if pressure still too low. |
| SPF |
300035 |
00 |
2 |
Length of cut |
IVLOC Hydraulic Oil Filter Pressure High . |
Reduced filter performance, no restriction on harvesting operation. |
| SPF |
300036 |
03 |
|
Knife sharpening |
Sharpening Door Potentiometer High. |
Sharpening door potentiometer failed or open circuit. |
| SPF |
300036 |
04 |
|
Knife sharpening |
Sharpening Door Potentiometer Low. |
Sharpening door potentiometer failed or short circuit. |
| SPF |
300036 |
13 |
3 |
Knife sharpening |
Sharpening Door Not Calibrated. |
Automatic knife sharpening operation not possible. |
| SPF |
300036 |
14 |
3 |
|
Sharpening Door Position Error. |
|
| SPF |
300037 |
03 |
|
Knife sharpening |
Sharpening Stone Potentiometer High. |
Sharpening stone potentiometer failed or open circuit. |
| SPF |
300037 |
04 |
|
Knife sharpening |
Sharpening Stone Potentiometer Low. |
Sharpening stone potentiometer failed or short circuit. |
| SPF |
300037 |
13 |
3 |
Knife sharpening |
Sharpening Stone Not Calibrated. |
Automatic knife sharpening operation not possible. |
| SPF |
300037 |
14 |
2 |
Knife sharpening |
Stone Position Error. |
|
| SPF |
300039 |
14 |
3 |
|
Main Clutch Denied Due To Cutterhead Reverse Operation. |
Main clutch denied. |
| SPF |
300040 |
09 |
|
Kernel processor adjust |
Left Kernel Processor Motor Sensor Failure. |
Kernel processor adjust cannot be performed. |
| SPF |
300041 |
09 |
|
Kernel processor adjust |
Right Kernel Processor Motor Sensor Failure. |
Kernel processor adjust cannot be performed. |
| SPF |
300042 |
14 |
|
|
LOC in Neutral (only 4-speed LOC). |
|
| SPF |
300043 |
14 |
|
|
676 Header - End Switch Input Short In Harness. |
|
| SPF |
300044 |
14 |
|
|
676 Header - Short In Harness To Battery. |
|
| SPF - SPFH Main Control Unit Diagnostic Trouble Codes |
| Control Unit |
SPN |
FMI |
Pri. |
Indicator Light |
Description |
Effect |
| SPF |
300045 |
14 |
|
|
676 Header - Wrong Header Selected. |
|
| SPF |
300046 |
14 |
|
|
676 Header - Reed Switch Failure. |
|
| SPF |
300047 |
14 |
|
|
676 Header - End Switch Input Stuck High. |
|
| SPF |
300048 |
14 |
|
|
676 Header - Harness Not Connected. |
|
| SPF |
300049 |
14 |
|
|
676 Header - Brake On. |
|
| SPF |
300050 |
01 |
3 |
Cutterhead speed or kernel processor adjust |
Cutterhead Speed Low For Harvesting. |
|
| SPF |
300052 |
01 |
2 |
Hydrostatic charge pressure |
Hydrostatic Charge Pressure Low. |
System pressure not sufficient for hydraulic function. |
| SPF |
300053 |
00 |
2 |
Hydrostatic oil temperature |
Hydrostatic Oil Temperature High. |
Hot oil can cause damage in hydraulic system. |
| SPF |
300054 |
01 |
2 |
Rotary air screen |
Rotary Air Screen Failed. |
|
| SPF |
300056 |
01 |
|
Battery 2 |
Alternator Not Charging. |
Risk of control unit shutdown due to low power supply. |
| SPF |
300056 |
05 |
|
Battery 2 |
Alternator Charging Detection Circuit Is Open Circuit. |
|
| SPF |
300057 |
00 |
3 |
|
Cutterhead Speed Sensor Failed or Drive Belt Slipping, Engine Speed to Cutterhead Speed Ratio Is High. |
Open loop control for cutterhead reverse and engine speed ratio for cutterhead forward operation. |
| SPF |
300057 |
01 |
3 |
|
Cutterhead Speed Sensor Failed, Engine Speed To Cutterhead Speed Ratio Is Low. |
Open loop control for cutterhead reverse and engine speed ratio for cutterhead forward operation. |
| SPF |
300057 |
02 |
2 |
Cutterhead Speed |
Cutterhead Speed Sensor Failed. |
Open loop for cutterhead reverse and engine speed ratio for cutterhead forward operation. |
| SPF |
300058 |
09 |
3 |
Stationary knife adjust |
No Knocks Detected While Moving Stationary Knife Towards Cutterhead on Left Side. |
|
| SPF |
300059 |
09 |
3 |
Stationary knife adjust |
No Knocks Detected While Moving Stationary Knife Towards Cutterhead on Right Side. |
|
| SPF |
300062 |
14 |
3 |
|
Manual Cutterhead Reverse Denied, Powr-Savr Operation Active. |
|
| SPF |
300064 |
14 |
3 |
|
Feed Roll Speed Not Reached. |
|
| SPF |
300068 |
14 |
|
|
Park Brake Applied Multi Function Lever Out Of Neutral. |
|