ARC Addresses - Armrest Control Unit

ARC - Armrest Control Unit
Addresses  
Number Type Description
002 Standard Beep Mode
003 Standard Limited System Beep Mode
004 Standard Analog Beep Mode
005 Standard Digital Beep Mode
080 Display Cab Temperature
081 Display Outlet Temperature
082 Display Inlet Temperature
083 Display Evaporator Temperature
100 Input Calibration Spout Fast Rotate Delay Configuration
Used to set the spout fast rotate delay.

NOTE: For detailed calibration procedure, see "Address ARC 100 Calibration - Spout Fast Rotate Delay Configuration" in this section.
101 Input Calibration Fast Throttle Speed
Used to set the fast throttle increase / decrease speed of the engine.
102 Input Calibration Slow Throttle Speed
Used to set the slow throttle increase / decrease speed of the engine.
103 Input Calibration Slow Throttle Speed Hold Time
Used to set the time the slow throttle speed engine acceleration is active before the high throttle engine speed acceleration becomes active.
104 Input Calibration Button 1 Configuration
Used to select the function for button 1 on the multi-function lever.

NOTE: For detailed calibration procedure, see "Address ARC 104 Calibration - Button 1 Configuration" in this section.
105 Input Calibration Button 2 Configuration
Used to select the function for button 2 on the multi-function lever.

NOTE: For detailed calibration procedure, see "Address ARC 105 Calibration - Button 2 Configuration" in this section.
106 Input Calibration Button 3 Configuration
Used to select the function for button 3 on the multi-function lever.

NOTE: For detailed calibration procedure, see "Address ARC 106 Calibration - Button 3 Configuration" in this section.
107 Input Calibration Circular Button Configuration
Used to select the function for the row guidance enable switch / selective control valve I on the multi-function lever.

NOTE: For detailed calibration procedure, see "Address ARC 107 Calibration - Circular Button Configuration" in this section.

 

OUCC020,0001EC1 -19-17OCT05-1/3

ARC - Armrest Control Unit
Addresses  
Number Type Description
108 Input Calibration Control Options (Operator)
Used to calibrate the operator control options.
The fifth digit from the left enables Automatic Output Mode for SCV II and Wagon Dump.
1 - Enables automatic output mode...XXXX
...1XXX
0 - Disables automatic output mode...XXXX
...0XXX

NOTE: In auto output mode, a double click turns on the output which will remain on even when the button is released. Address ARC 109, ARC 111, ARC 112 and ARC 113 defines the time-out period for the output.
The sixth digit from the left MUST remain unchanged .

The seventh digit from the left enables Automatic Actuation Raise.
1 - Indicates the automatic actuation. Drives the SCV I + (raise) output when the metal detector trips...XXXX
...XX1X
0 - Disables Automatic Actuation Raise...XXXX
...XX0X

The eighth digit from the left enables Automatic Actuation Lower.
1 - Indicates the automatic actuation. Drives the SCV I - (lower) output after the feed rolls are engaged in the forward direction...XXXX
...XXX1
0 - Disables Automatic Actuation Lower...XXXX
...XXX0

 

OUCC020,0001EC1 -19-17OCT05-2/3

ARC - Armrest Control Unit
Addresses  
Number Type Description
109 Input Calibration SCV II Auto Output Mode Time-Out
Used to calibrate the time-out for automatic output mode.

NOTE: For detailed calibration procedure, see "Address ARC 109 Calibration - SCV II Auto Output Mode Time-Out" in this section.
110 Input Calibration Automatic Actuation Lower Delay
Used to calibrate the delay between feed rolls turning forward and driving the SCV I - output.

NOTE: For detailed calibration procedure, see "Address ARC 110 Calibration - Automatic Actuation Lower Delay" in this section.
111 Input Calibration Automatic Spout Tilt Up Time-Out
Used to calibrate the time-out for automatic spout tilt up.

NOTE: For detailed calibration procedure, see "Address ARC 111 Calibration - Automatic Spout Tilt Up Time-Out" in this section.
112 Input Calibration Automatic Spout Rotate Time-Out
Used to calibrate the time-out for automatic spout rotate.

NOTE: For detailed calibration procedure, see "Address ARC 112 Calibration - Automatic Spout Rotate Time-Out" in this section.
113 Input Calibration Wagon Dump Automatic Output Mode Time-Out
Used to calibrate the time-out for automatic output mode.

NOTE: For detailed calibration procedure, see "Address ARC 113 Calibration - Wagon Dump Automatic Output Mode Time-Out" in this section.
119 Interactive Calibration Row Guidance Potentiometer Calibration
Used to calibrate the row guidance potentiometer.
198 Display - Operator Cutterhead Operating Time
199 Display - Operator Machine Operating Time

 

OUCC020,0001EC1 -19-17OCT05-3/3