RCP Addresses - Corner Post Control Unit

RCP - Corner Post Control Unit
Addresses  
Number Type Description
002 Standard Beep Mode
003 Standard Limited System Beep Mode
004 Standard Analog Beep Mode
005 Standard Digital Beep Mode
010 Analog Input ATC Blower Speed Potentiometer
Display in Volts
011 Analog Input Back-Lighting Voltage Level
Display in Volts
012 Analog Input ATC Reference Voltage
Display in Volts
013 Analog Input Battery Voltage
Display in Volts
014 Analog Input ATC Temperature Set Point Potentiometer
Display in Volts
080 Display Engine Power Level
Used to display the engine power level value transmitted by the armrest control unit.
081 Display Rear Drive Controller Software Part Number
Used to display the software part number transmitted by the rear drive controller.
082 Display Rear Drive Controller Software Revision Number
Used to display the software revision number transmitted by the rear drive controller.
083 Display Rear Drive Controller Hardware Part Number
Used to display the hardware part number transmitted by the rear drive controller.
100 Input Calibration Tire Size Calibration
Used to calibrate the tire size.
Rolling radius calibration chart for all Self-Propelled Forage Harvester
Tire size: 16.5/85-24 - Input: 00620
Tire size: 18.4-26 - Input: 00670
Tire size: 24.5 - 32 - Input: 00840
Tire size: 480/80 R26 - Input: 00665
Tire size: 540/65 R26 - Input: 00695
Tire size: 580/70 R26 - Input: 00670
Tire size: 620/75 R34 - Input: 00860
Tire size: 650/75 R32 - Input: 00840
Tire size: 800/65 R32 - Input: 00870
Tire size: 900/55 R32 - Input: 00840
Tire size: 1050/50 R32 - Input: 00855

 

OUCC020,0001EC5 -19-20JUL04-1/6

RCP - Corner Post Control Unit
Addresses  
Number Type Description
101 Interactive Calibration Rear Wheel Drive Control Unit Calibration
Used to calibrate the rear wheel drive control unit.

NOTE: For detailed calibration procedure see "Address RCP 101 Calibration - Rear Wheel Drive Control Unit" in this section.This teaching ratio can be displayed with address RCP 102.
102 Calibration (Read only) Rear Wheel Drive Control Unit Teaching Ratio
Displays the current rear wheel drive control unit teaching ratio.
103 Input Calibration Display Configuration (Operator)
The first digit from the left enables storage of diagnostic trouble codes (DTCs) for all controllers.
1 - enables storage of DTCs...1XXX
...XXXX

0 - disables storage of DTCs...0XXX
...XXXX

The second digit from the left controls the Ground Speed Display Units.
1 - SI units (km/h)...X1XX
...XXXX

0 - English units (mph)...X0XX
...XXXX

The third digit from the left controls the Pressure Display Units I.
1 - SI units (bars)...XX1X
...XXXX

0 - English units (PSI)...XX0X
...XXXX

 

OUCC020,0001EC5 -19-20JUL04-2/6

RCP - Corner Post Control Unit
Addresses  
Number Type Description
103
Continuation		 Input Calibration The fourth digit from the left controls the Pressure Display Units II.
1 - SI units (bars)...XXX1
...XXXX

0 - English units (PSI)...XXX0
...XXXX

The fifth digit from the left controls the Area Display Units.
1 - SI units...XXXX
...1XXX

0 - English units...XXXX
...0XXX

The sixth digit from the left controls the Linear Length Display Units.
1 - SI units...XXXX
...X1XX

0 - English units...XXXX
...X0XX

The seventh digit from the left controls the Enable / Disable the Clock.
1 - Enables the clock...XXXX
...XX1X

0 - Disables the clock...XXXX
...XX0X

The eighth digit from the left controls the Clock Display Mode.
1 - 24 hour display...XXXX
...XXX1

0 - 12 hour display...XXXX
...XXX0

NOTE: Pressure Display Units II: This is only used if Pressure Display Units I are set to select SI units.
104 Input Calibration Operator Options
To configure the area counter and cutterhead hours function for:per fieldper dayper season cutterhead hour counterThe total cutterhead hour counter is still counting the real cutterhead hours when main clutch is engaged.
Default: The cutterhead hours per field, per day and per season are counted with the main clutch engaged.

 

OUCC020,0001EC5 -19-20JUL04-3/6

RCP - Corner Post Control Unit
Addresses  
Number Type Description
104
Continuation		 Input Calibration The third digit from the left controls the Fuel Accumulation for use in the Hour Counter.
1 - Indicates the fuel accumulation constantly ...XX1X
...XXXX

0 - Indicates the fuel accumulation only when the time is accumulated ...XX0X
...XXXX
Default setting...XX1X
...XXXX

The fourth digit from the left controls the Engine Load or Cutterhead Speed on Display.
1 - Enables the engine load...XXX1
...XXXX

0 - Disables the engine load (cutterhead speed displayed instead)...XXX0
...XXXX
Default setting...XXX0
...XXXX
104
Continuation		 Input Calibration The fifth digit from the left controls the Area Counter Beep.
1 - Enables the area counter beep...XXXX
...1XXX

0 - Disables the area counter beep ...XXXX
...0XXX
Default setting...XXXX
...0XXX

The sixth digit from the left controls the Cutterhead Hours Counter Activation Option 1: Feedrolls Forward Activation.
1 - Activates option 1...XXXX
...X1XX

0 - Deactivates option 1...XXXX
...X0XX
Default setting...XXXX
...X0XX

 

OUCC020,0001EC5 -19-20JUL04-4/6

RCP - Corner Post Control Unit
Addresses  
Number Type Description
104
Continuation		 Input Calibration The seventh digit from the left controls the Cutterhead Hours Counter Activation Option 2: Harvesting Position Activation.
1 - Activates option 2...XXXX
...XX1X

0 - Deactivates option 2...XXXX
...XX0X
Default setting...XXXX
...XX0X

The eighth digit from the left controls the Cutterhead Hours Counter Activation Option 3: Vehicle Forward Activation
1 - Activates option 3...XXXX
...XXX1

0 - Deactivates option 3...XXXX
...XXX0
Default setting...XXXX
...XXX0
104
Continuation		 Input Calibration

NOTE: Option 1: The cutterhead hours are counted with the main clutch engaged AND feedrolls forward.

NOTE: Option 2: The cutterhead hours are counted with the main clutch engaged, feedrolls forward AND the header in harvesting position.

NOTE: Option 3: The cutterhead hours are counted with the main clutch engaged, feedrolls forward, the header in harvesting position AND the vehicle in forward travel

NOTE: If only cutterhead hours activation option 2 is activated, the corresponding rules for cutterhead hours activation option 1 are applied.

NOTE: If only cutterhead hours activation option 3 is activated, the corresponding rules for cutterhead hours activation option 1 and option 2 are applied.

 

OUCC020,0001EC5 -19-20JUL04-5/6

RCP - Corner Post Control Unit
Addresses  
Number Type Description
105 Interactive Calibration Intermittent Wiper Interval
Used to set the interval time of the wiper.

NOTE: For detailed calibration procedure see "Address RCP 105 Calibration - Intermittent Wiper Interval" in this section.
106 Interactive Calibration Intermittent Wiper Sweep Time
Used to set the intermittent sweep time of the wiper.

NOTE: For detailed calibration procedure see "Address RCP 106 Calibration - Intermittent Wiper Sweep Time" in this section.
116 Interactive Calibration Rear Wheel Drive Control Unit Pressure Sensor
Used to calibrate the rear wheel drive control unit pressure sensor.
117 Interactive Calibration ATC Temperature Potentiometer Calibration
Used to calibrate the ATC temperature potentiometer.
118 Interactive Calibration ATC Fan Potentiometer Calibration
Used to calibrate the ATC fan potentiometer.
119 Interactive Calibration Potentiometer Calibration of Dimmer for Cab Interior Light
Used to calibrate the potentiometer of the dimmer for cab interior light.
180 Input Calibration Available Rows Calibration
Used to set the maximum number of rows available for the area counter.
181 Display Actual Rows
Used to read the actual number of rows selected by the operator for the area counter.
182 Display Actual Row Width
Used to read the actual row width selected by the operator for the area counter.
Row width is displayed in cm.
183 Display Working Header Width
Used to read the working header width selected by the operator for the area counter.
This value is the actual number of rows times the actual row width selected by the operator.
The working header width is displayed in cm.
194 Display Fuel Rate
Used to read the fuel rate.
The total fuel used is in units of 0.1 liters/hours (0.025 U.S gal./hours).
195 Display Total Fuel Used
Used to read the total fuel consumption.
The total fuel consumption is in units of 0.1 liters (0.025 U.S gal.).
196 Display Total Accumulated Area
Used to read the total accumulated area.
The total accumulated area is in units of 0.001 ha.
197 Display Time Of Day
Used to read the time of day from the clock.
The format is hours + minutes.
198 Display - Operator Cutterhead Operating Hours
199 Display - Operator Machine Operating Hours

 

OUCC020,0001EC5 -19-20JUL04-6/6