Predelivery Inspection

Dealer's name Town Dealer's Account No. J.D. Branch No.
     
Servicing Dealer, if not identical with above - Name, Address
 
Customer (initials and surname) Street + No.
   
Town and Postcode Vehicle Registration No.
   
Delivery Date Day Month Year Machine Name A = Farmer
B = Contractor                                                
                  C = Commercial
Product Identification No. (Serial No.) Customer Group D = Community
                          A [squ ] B [squ ] C [squ ] D [squ ] E [squ ] E = Home Owner
TO THE DEALER
THE FOLLOWING PREDELIVERY SERVICE MUST be performed by you. Refer to the Operator's
Manual for detailed information.
[squ ] 1. Lubricate all grease fittings. [squ ] 3. Check tire pressures; adjust if necessary. [squ ] 5. Adjust combine and cutting platform for crop to be harvested.
[squ ] 2. Tighten all wheel bolts and nuts to specified torque. [squ ] 4. Clean the combine thoroughly out.    
The following inspections have been made at the factory. Prior to delivery the following items must be rechecked by you. Refer to the Operator's Manual and the Technical Manual for detailed information.
Mark the YES box if condition WAS FOUND acceptable, or NO, if not. If the answer is NO, give a short explanation in the "COMMENTS" column. Following this, make corrections if necessary prior to delivery.

 

ZX,CHECKLISTSLC -19-01DEC98-1/2

Yes No     Yes No     Yes No    
[squ ] [squ ] 1. Engine crankcase oil level correct? [squ ] [squ ] 12. Hydrostatic ground speed drive operating correctly? [squ ] [squ ] 21. All rubber seals in separator area and cleaning unit OK?
[squ ] [squ ] 2. Engine coolant level correct? [squ ] [squ ] 13. Engine shut-off device oper ating correctly? [squ ] [squ ] 22. All belts and chains adjusted correctly?
[squ ] [squ ] 3. Hydraulic oil level correct?                
[squ ] [squ ] 4. Lights OK? [squ ] [squ ] 14. Reverser operating correctly? [squ ] [squ ] 23. All guards, shields etc. installed?
[squ ] [squ ] 5. Steering OK? [squ ] [squ ] 15. Final drive oil level OK?        
[squ ] [squ ] 6. Foot brakes OK? [squ ] [squ ] 16. Transmission oil level OK? [squ ] [squ ] 24. Paint and decals smooth and neat?
[squ ] [squ ] 7. Parking brake OK? [squ ] [squ ] 17. Fast idle speed of engine correct (2350 + 50 rpm)?        
[squ ] [squ ] 8. Gauges, acoustic warning devices and monitors functioning properly? [squ ] [squ ] 18. Straw walkers functioning correctly? [squ ] [squ ] 25. Have all controls and safety rules etc. been explained to the operator?
[squ ] [squ ] 9. Transmission operating correctly? [squ ] [squ ] 19. Cutting platform drive shaft line-up OK? [squ ] [squ ] 26. Cutting platform bottom angle OK?
[squ ] [squ ] 10. Cutting platform knife bar alignment OK? [squ ] [squ ] 20. Cutting platform auger position OK? [squ ] [squ ] 27. Cutting platform reel lowest position OK?
[squ ] [squ ] 11. Cutting platform knife distance to auger OK?                
COMMENTS:  
   
   
Delivery Report and Operator's Manual OMZ92614 Issue M8
were handed over to the customer together with the machine.		      
  Dealer - Service Technician   Date
DISTRIBUTION:
1-white = JD Sales Branch, 2-green = Factory, 3-yellow = JD Dealer, 4-blue = Servicing Dealer, 5-pink = Customer

 

ZX,CHECKLISTSLC -19-01DEC98-2/2