C00 Armrest Control Unit

Diagnostic Addresses - C00 Armrest Control Unit

Control Unit Add. Line 2 Line 3 Description Details
Armrest C00 1 nnnn nn.nn Diagnostic Trouble Codes "none" - indicates there are no Diagnostic Trouble Codes.
"code" - indicates there are Diagnostic Trouble Codes available.
Push ENTER button to view codes. Use ARROW-UP and ARROW-DOWN to scroll through list of codes.
Armrest C00 2 _ _ _ _ nnnn BEEP: System The system will show the diagnostic address of any input that changes. Pushing the Enter Button will navigate to that address to display the status of that input.
Armrest C00 3 _ _ _ _ nnnn BEEP: Analog Inputs The analog inputs are HEADERTRAK Sensitivity, HEADERTRAK Rate , Discharge Beater Speed Sensor, System Battery Voltage, and the Sensor Voltage. The system will show the diagnostic address of any analog input voltage that changes. Pushing the Enter Button will navigate to that address to display the status of that input.
Armrest C00 4 _ _ _ _ nnnn BEEP: Frequency Inputs The system will show the diagnostic address of Discharge Beater Speed input if it changes. Pushing the Enter Button will navigate to that address to display the status of that input.
Armrest C00 5 _ _ _ _ nnnn BEEP: Armrest Console and Multifunction Lever Inputs The system will show the diagnostic address of any Armrest Console switch or Multifunction Lever switch that changes. Pushing the Enter Button will navigate to that address to display the status of that input.
Armrest C00 6 _ _ _ _ nnnn BEEP: Discrete Digital Inputs The discrete digital inputs are the Separator Engage FET Status, CLIMATRAK Pressurizer FET Status, Throttle Status (9450), Seat Switch, CLIMATRAK Low Pressure Switch, Header Engage Switch, Separator Engage Switch, Header Engage Switch - Reverse Position, Header Engage FET Status and Neutral Gate Switch. The system will show the diagnostic address of any discrete digital input that changes. Pushing the Enter Button will navigate to that address to display the status of that input.
Armrest C00 10 _ _ _ _ nn.nn DISPLAY: Delayed Power (cc# 006) voltage Analog voltage shown in Volts DC
Armrest C00 11 _ _ _ _ nn.nn DISPLAY: CAN Hi (cc# 965) voltage Analog voltage shown in Volts DC
Armrest C00 12 _ _ _ _ nn.nn DISPLAY: CAN Lo (cc# 964) voltage Analog voltage shown in Volts DC

 

OUZXMAG,00018A8 -19-10OCT02-1/9

Control Unit Add. Line 2 Line 3 Description Details
Armrest C00 13 _ _ _ _ _n.nn DISPLAY: Armrest Sensor Power (cc# 032) voltage for HEADERTRAK Sensitivity Adjust, HEADERTRAK Rate Adjust, DIAL-A-SPEED Encoder and HEADERTRAK Height Encoder Analog voltage shown in Volts DC
Armrest C00 14 _ _ _ _ nn.nn DISPLAY: Multifunction Lever supply voltage Analog voltage shown in Volts DC
Armrest C00 15 _ _ _ _ nn.nn DISPLAY: Control Circuit Power (cc# 023) voltage Analog voltage shown in Volts DC
Armrest C00 16 _ _ _ _ nn.nn DISPLAY: Header Engage Switch voltage Analog voltage shown in Volts DC
Armrest C00 17 _ _ _ _ nn.nn DISPLAY: Separator Engage Switch voltage Analog voltage shown in Volts DC
Armrest C00 19 _ _ _ _ _n.nn DISPLAY: HEADERTRAK - Height Sensitivity (cc# 494) voltage Analog voltage shown in Volts DC
Armrest C00 20 _ _ _ _ _n.nn DISPLAY: HEADERTRAK - Height Change Rate (cc# 495) voltage Analog voltage shown in Volts DC
Armrest C00 21 _ _ _ _ _n.nn DISPLAY: CLIMATRAK Outside Air Temperature Sensor (cc# 764) voltage Analog voltage shown in Volts DC
Armrest C00 22 _ _ _ _ _n.nn DISPLAY: CLIMATRAK Outlet Air Temperature Sensor (cc# 757) voltage Analog voltage shown in Volts DC
Armrest C00 23 _ _ _ _ _n.nn DISPLAY: CLIMATRAK Cab Air Temperature Sensor (cc# 758) voltage Analog voltage shown in Volts DC
Armrest C00 24 _ _ _ _ _n.nn DISPLAY: CLIMATRAK Core Temperature Sensor (cc# 759) voltage Analog voltage shown in Volts DC
Armrest C00 25 _ _ _ _ _n.nn DISPLAY: CLIMATRAK Solar Sensor (cc# 763) voltage Analog voltage shown in Volts DC
Armrest C00 26 _ _ _ _ _n.nn DISPLAY: CLIMATRAK Water Valve Position (cc# 765) voltage Analog voltage shown in Volts DC
Armrest C00 29 _ _ _ _ nnn.n DISPLAY: Discharge Beater Speed (cc# 626) Frequency shown in Hertz
Armrest C00 30 _ _ _ _ 1xxx DISPLAY: Header Raise Fast Button status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 30 _ _ _ _ x1xx DISPLAY: Header Raise Button status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 30 _ _ _ _ xx1x DISPLAY: Header Lower Fast Button status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 30 _ _ _ _ xxx1 DISPLAY: Header Lower Button status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 31 _ _ _ _ 1xxx DISPLAY: HEADERTRAK - Tilt Left Button status 1 = switch pushed
0 = switch released
3 = undefined input

 

OUZXMAG,00018A8 -19-10OCT02-2/9

Control Unit Add. Line 2 Line 3 Description Details
Armrest C00 31 _ _ _ _ x1xx DISPLAY: HEADERTRAK - Tilt Right Button status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 31 _ _ _ _ xx1x DISPLAY: Unloading Auger Engage Button status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 31 _ _ _ _ xxx1 DISPLAY: Quick Stop Button status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 32 _ _ _ _ 1xxx DISPLAY: Unloading Auger Swing Out Button (Automatic) status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 32 _ _ _ _ x1xx DISPLAY: Unloading Auger Swing Out Button (Manual) status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 32 _ _ _ _ xx1x DISPLAY: Unloading Auger Swing In Button (Automatic) status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 32 _ _ _ _ xxx1 DISPLAY: Unloading Auger Swing In Button (Manual) status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 33 _ _ _ _ 1xxx DISPLAY: Reel Fore Button (Open Deck Plate Button) status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 33 _ _ _ _ x1xx DISPLAY: Reel Aft Button (Close Deck Plate Button) status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 33 _ _ _ _ xx1x DISPLAY: Reel Raise Button status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 33 _ _ _ _ xxx1 DISPLAY: Reel Lower Button status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 34 _ _ _ _ x1xx DISPLAY: Header Activation 3 Button status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 34 _ _ _ _ xx1x DISPLAY: Header Activation 2 Button status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 34 _ _ _ _ xxx1 DISPLAY: Header Activation 1 Button status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 38 _ _ _ _ x1xx DISPLAY: Hi Idle Button Status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 38 _ _ _ _ xx1x DISPLAY: Mid Idle Button Status 1 = switch pushed
0 = switch released
3 = undefined input

 

OUZXMAG,00018A8 -19-10OCT02-3/9

Control Unit Add. Line 2 Line 3 Description Details
Armrest C00 38 _ _ _ _ xxx1 DISPLAY: Lo Idle Button status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 39 _ _ _ _ 1xxx DISPLAY: Reel Speed Increase Button status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 39 _ _ _ _ x1xx DISPLAY: Reel Speed Decrease Button status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 39 _ _ _ _ xx1x DISPLAY: Draper Speed Increase Button status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 39 _ _ _ _ xxx1 DISPLAY: Draper Speed Decrease Button status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 40 _ _ _ _ 1xxx DISPLAY: Cleaning Fan Speed Increase Button status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 40 _ _ _ _ x1xx DISPLAY: Cleaning Fan Speed Decrease Button status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 40 _ _ _ _ xx1x DISPLAY: Cylinder (Threshing) Speed Increase Button status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 40 _ _ _ _ xxx1 DISPLAY: Cylinder (Threshing) Speed Decrease Button status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 41 _ _ _ _ 1xxx DISPLAY: Concave (Threshing) Clearance Increase Button status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 41 _ _ _ _ x1xx DISPLAY: Concave (Threshing) Clearance Decrease Button status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 41 _ _ _ _ xx1x DISPLAY: Hillmaster Tilt Left Button status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 41 _ _ _ _ xxx1 DISPLAY: Hillmaster Tilt Right Button status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 42 _ _ _ _ 1xxx DISPLAY: Chopper Vane Left Button status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 42 _ _ _ _ x1xx DISPLAY: Chopper Vane Right Button status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 43 _ _ _ _ 1xxx DISPLAY: Grain Tank Cover Open Button status 1 = switch pushed
0 = switch released
3 = undefined input

 

OUZXMAG,00018A8 -19-10OCT02-4/9

Control Unit Add. Line 2 Line 3 Description Details
Armrest C00 43 _ _ _ _ x1xx DISPLAY: Grain Tank Cover Close Button status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 46 _ _ _ _ 1xxx DISPLAY: Road / Field Button status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 46 _ _ _ _ x1xx DISPLAY: Hillmaster Engage Button status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 46 _ _ _ _ xx1x DISPLAY: Four Wheel Drive Speed Lo Button status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 46 _ _ _ _ xxx1 DISPLAY: Four Wheel Drive Speed Hi Button status 1 = switch pushed
0 = switch released
3 = undefined input
Armrest C00 50 _ _ 11 xxxx DISPLAY: Separator Engage Switch input 11 = ENGAGED
00 = DISENGAGED
01 = Switch failure
10 = Switch failure
Armrest C00 50 _ _ xx x111 DISPLAY: Header Engage Switch input 001 = ENGAGED FORWARD
111 = ENGAGED REVERSE
010 = DISENGAGED
011 = Switch failure
000 = Switch failure
001 = Switch failure
110 = Switch failure
101 = Switch failure
Armrest C00 51 _ _ _ _ xx1x DISPLAY: Operator Presence Sensor (cc# 804) input 1 = operator in seat
0 = operator out of seat
3 = undefined input
Armrest C00 51 _ _ _ _ xxx1 DISPLAY: Multifunction Lever Position Signal (cc# 822) input 1 = Multifunction Lever not in neutral
0 = Multifunction Lever in neutral
3 = undefined input
Armrest C00 52 _ _ _ _ _ 1xx DISPLAY: Status of Beater Speed input 1 = beater speed input open
0 = beater speed input shorted to ground
Armrest C00 53 x1xx xxxx DISPLAY: Status of output to Header Clutch 1 = output normal
0 = output shorted or open
Armrest C00 54 xx1x xxxx DISPLAY: Status of output to Separator Engage Valve 1 = output normal
0 = output shorted or open
Armrest C00 60 _ _ _ _ _ _ 1x DISPLAY: CAN Bus message from the Left Control Unit - Key Switch 1 = START
0 = OFF
3 = undefined input
Armrest C00 60 _ _ _ _ _ _ x1 DISPLAY: CAN Bus message from the Left Control Unit - Key Switch 1 = RUN
0 = OFF
3 = undefined input
Armrest C00 61 _ _ _ _ 1xxx DISPLAY: CAN Bus message from the Left Control Unit - Low Speed Four Wheel Drive Indicator 1 = on
0 = off
2 = flashing
3 = undefined input

 

OUZXMAG,00018A8 -19-10OCT02-5/9

Control Unit Add. Line 2 Line 3 Description Details
Armrest C00 61 _ _ _ _ x1xx DISPLAY: CAN Bus message from the Left Control Unit - High Speed Four Wheel Drive Indicator 1 = on
0 = off
2 = flashing
3 = undefined input
Armrest C00 61 _ _ _ _ xx1x DISPLAY: CAN Bus message from the Left Control Unit - Hillmaster Engaged Indicator 1 = on
0 = off
2 = flashing
3 = undefined input
Armrest C00 61 _ _ _ _ xxx1 DISPLAY: CAN Bus message from the Left Control Unit - Auger Engaged Indicator 1 = on
0 = off
2 = flashing
3 = undefined input
Armrest C00 62 _ _ _ _ _ 1xx DISPLAY: CAN Bus message from the Cornerpost Control - CLIMATRAK Defog Switch 1 = closed
0 = open
3 = undefined input
Armrest C00 62 _ _ _ _ _ x1x DISPLAY: CAN Bus message from the Cornerpost Control - CLIMATRAK Auto/Manual Fan Speed Switch 1 = AUTO (closed)
0 = MANUAL (open)
3 = undefined input
Armrest C00 62 _ _ _ _ _ xx1 DISPLAY: CAN Bus message from the Cornerpost Control - CLIMATRAK On/Off Switch 1 = ON (closed)
0 = OFF (open)
3 = undefined input
Armrest C00 63 _ _ _ _ _ xxx DISPLAY: CAN Bus message from the Cornerpost Control - CLIMATRAK Temperature Setpoint Shown in °C or °F
Armrest C00 64 _ _ _ _ _ xxx DISPLAY: CAN Bus message from the Cornerpost Control Unit - CLIMATRAK Fan Speed Setpoint Shown in percent
Operating Range = 30% - 100%
Armrest C00 65 _ _ _ _ _ xxx DISPLAY: CAN Bus message from Engine Control Unit - Engine Speed Shown in rpm
Armrest C00 70 _ _ _ _ _ nnn DISPLAY: Height Control Encoder position As the encoder is rotated clockwise the number will increase. As the encoder is rotated counter clockwise the number will decrease.
Range = 0 - 255
Armrest C00 71 _ _ _ _ _ nnn DISPLAY: DIAL-A-SPEED Encoder position As the encoder is rotated clockwise the number will increase. As the encoder is rotated counter clockwise the number will decrease.
Range = 0 - 255
Armrest C00 72 _ _ _ _ nnnn DISPLAY: CLIMATRAK operating mode 1 = Air Conditioning
0 = Heating
Armrest C00 73 _ _ _ _ nnn.n DISPLAY: CLIMATRAK Cab Air Temperature Shown in °C or °F
Armrest C00 74 _ _ _ _ nnn.n DISPLAY: CLIMATRAK Outlet Air Temperature Shown in °C or °F
Armrest C00 75 _ _ _ _ nnn.n DISPLAY: CLIMATRAK Outside Air Temperature Shown in °C or °F
Armrest C00 76 _ _ _ _ nnn.n DISPLAY: CLIMATRAK Core Temperature Shown in °C or °F

 

OUZXMAG,00018A8 -19-10OCT02-6/9

Control Unit Add. Line 2 Line 3 Description Details
Armrest C00 77 _ _ _ _ _ _ 1x DISPLAY: CLIMATRAK Recirculation Fan Relay signal (cc# 928) 1 = on
0 = off
Armrest C00 77 _ _ _ _ _ _ x1 DISPLAY: CAN Bus message to the Left Control Unit - CLIMATRAK Clutch (cc# 913) 1 = on
0 = off
Armrest C00 78 _ nnn _ xxx DISPLAY: Water valve commanded position Shown in percent
100 = Full open
Armrest C00 78 _ xxx _ nnn DISPLAY: Water valve actual position Shown in percent
100 = Full open
Armrest C00 79 _ _ _ _ _ nnn DISPLAY: Recirculation Fan Speed Shown in percent
100 = Maximum speed
Armrest C00 80 _ _ _ _ nnnn DISPLAY: Armrest Control Unit Hours Time (shown in hours) the Armrest Control Unit has been powered.
Armrest C00 90 _ _ _ _ 1xxx DISPLAY: Status of Header Engage Switch for Start Interlock 1 = output to clutch turned off. Interlock will allow engine start.
0 = output to clutch turned on. Interlock will not allow engine start.
Armrest C00 90 _ _ _ _ x1xx DISPLAY: Status of Separator Engage Switch for Start Interlock 1 = output to valve turned off. Interlock will allow engine start.
0 = output to valve turned on. Interlock will not allow engine start.
Armrest C00 90 _ _ _ _ xx1x DISPLAY: Status of Multifunction Lever Position Signal (cc# 822) used for Start Interlock 1 = Multifunction lever in neutral gate. Interlock will allow engine start.
0 = Multifunction lever not in neutral gate. Interlock will not allow engine start.
Armrest C00 90 _ _ _ _ xxx1 DISPLAY: Status of OK to Start output to Left Control Unit 1 = output to relay turned on
0 = output to relay turned off
Armrest C00 91 xxxx 1xxx DISPLAY: Road / Field mode used for separator interlock 1 = Combine is in FIELD. Interlock will allow separator to be engaged.
0 = Combine is in ROAD. Interlock will not allow separator to be engaged.
Armrest C00 91 xxxx x1xx DISPLAY: Separator Engage driver status 1 = indicates the separator engage valve and wiring are ok.
0 = separator engage valve or wiring are shorted or open.
Armrest C00 91 xxxx xx1x DISPLAY: Separator Engage Switch input 1 = switch on
0 = Switch off
3 = undefined input
Armrest C00 91 xxxx xxx1 DISPLAY: Separator Engage (cc# 302) 1 = separator engage signal sent by controller to separator engage valve.
Armrest C00 92 xx1x xxxx DISPLAY: Status of Quick Stop used for separator interlock 1 = Quick Stop Button is not pushed. Interlock will allow separator to be engaged.
0 = Quick Stop Button is pushed. Interlock will not allow separator to be engaged.
Armrest C00 92 xxx1 xxxx DISPLAY: Driver Position Sensor (cc# 804) used for header engage interlock 1 = Operator is present. Interlock will allow header to be engaged.
0 = Operator not present. Interlock will not allow header to be engaged.

 

OUZXMAG,00018A8 -19-10OCT02-7/9

Control Unit Add. Line 2 Line 3 Description Details
Armrest C00 92 xxxx 1xxx DISPLAY: Road / Field mode used for header engage interlock 1 = Combine is in FIELD. Interlock will allow header to be engaged.
0 = Combine is in ROAD. Interlock will not allow header to be engaged.
Armrest C00 92 xxxx x1xx DISPLAY: Header Engage driver status 1 = indicates the header engage clutch and wiring are ok.
0 = header engage clutch or wiring are shorted or open.
Armrest C00 92 xxxx xx1x DISPLAY: Header Engage Switch input 1 = switch on
0 = switch off
3 = undefined input
Armrest C00 92 xxxx xxx1 DISPLAY: Header Engage command to driver 1 = Header Engage output on
0 = Output off
Armrest C00 93 1xxx xxxx DISPLAY: CLIMATRAK High Pressure Switch 1 = closed
0 = open
Armrest C00 93 x1xx xxxx DISPLAY: CLIMATRAK Low Pressure Switch 1 = closed
0 = open
Armrest C00 93 xx11 xxxx DISPLAY: CLIMATRAK logic results from temperature sensor inputs 11 = clutch commanded ON
01 = clutch commanded OFF
10 = clutch commanded OFF
00 = clutch commanded OFF
Armrest C00 93 xxxx 1xxx DISPLAY: CLIMATRAK Evaporator Core 1 = core temperature above 0°C / 32°F
0 = core temperature below 0°C / 32°F
Armrest C00 93 xxxx x1xx DISPLAY: CLIMATRAK Cool / Heat mode 1 = Cooling
0 = Heating
Armrest C00 93 xxxx xx1x DISPLAY: CAN Bus message sent to Left Control Unit to request CLIMATRAK Compressor Clutch 1 = ON
0 = OFF
Armrest C00 93 xxxx xxx1 DISPLAY: CAN Bus message from Left control Unit indicating CLIMATRAK Compressor Clutch output status 1 = ON
0 = OFF
Armrest C00 100     DISPLAY/MODIFY: HEADERTRAK Rate Adjust interactive calibration  
Armrest C00 101     DISPLAY/MODIFY: HEADERTRAK Sensitivity Adjust interactive calibration  
Armrest C00 110 _ _ _ _ 1xxx DISPLAY/MODIFY: High Speed Four Wheel Drive Indicator 1 = ON
2 = Flashing
0 = OFF
Armrest C00 110 _ _ _ _ x1xx DISPLAY/MODIFY: Road / Field Indicator 1 = ON
2 = Flashing
0 = OFF
Armrest C00 110 _ _ _ _ xx1x DISPLAY/MODIFY: Hillmaster Indicator 1 = ON
2 = Flashing
0 = OFF
Armrest C00 110 _ _ _ _ xxx1 DISPLAY/MODIFY: Low Speed Four Wheel Drive Indicator 1 = ON
2 = Flashing
0 = OFF

 

OUZXMAG,00018A8 -19-10OCT02-8/9

Control Unit Add. Line 2 Line 3 Description Details
Armrest C00 111 _ _ _ _ 1xxx DISPLAY/MODIFY: Unloading Auger Engaged Indicator 1 = ON
2 = Flashing
0 = OFF
Armrest C00 111 _ _ _ _ x1xx DISPLAY/MODIFY: Hi Idle Indicator 1 = ON
2 = Flashing
0 = OFF
Armrest C00 111 _ _ _ _ xx1x DISPLAY/MODIFY: Mid Idle Indicator 1 = ON
2 = Flashing
0 = OFF
Armrest C00 111 _ _ _ _ xxx1 DISPLAY/MODIFY: Low Idle Indicator 1 = ON
2 = Flashing
0 = OFF
Armrest C00 112 xxxx x1xx DISPLAY/MODIFY: OK to Start (cc#108) 1 = ON
2 = Flashing
0 = OFF
Armrest C00 112 xxxx xx1x DISPLAY/MODIFY: Pressurizer Fan (cc# 928) 1 = ON
2 = Flashing
0 = OFF
Armrest C00 112 xxxx xxx1 DISPLAY/MODIFY: Tri-State Throttle (cc# 143) (9450 only) 1 = ON
2 = Flashing
0 = OFF
Armrest C00 113 _ _ _ _ _ _ 1x DISPLAY/MODIFY: Separator Engage (cc# 302)

NOTE: Switch must be ENGAGED and Engine not Running

 1 = ON
2 = Flashing
0 = OFF
Armrest C00 113 _ _ _ _ _ _ x1 DISPLAY/MODIFY: Header Engage (cc#402)

NOTE: Switch must be ENGAGED and Engine not Running

 1 = ON
2 = Flashing
0 = OFF
Armrest C00 120 _ _ _ _ _ xx.x DISPLAY: CLIMATRAK Water Valve Command Signal (cc# 762) voltage Shown in V DC ± 0.5
Armrest C00 121 _ _ _ _ _ xx.x DISPLAY: Blower Motor Command Signal (cc#939) voltage Shown in V DC ± 0.1
Armrest C00 227 _ _ nn nnnn DISPLAY: Part number of the boot block program  
Armrest C00 228 _ _ _ _ nnnn DISPLAY: Version number of the boot block program  
Armrest C00 233 _ _ nn nnnn DISPLAY: Base program part number  
Armrest C00 234 _ _ _ _ nnnn DISPLAY: Base program version number  
Armrest C00 235 _ _ nn nnnn DISPLAY: Device part number  
Armrest C00 236 _ _ _ _ nnnn DISPLAY: Device Serial Number  
Armrest C00 247 _ _ _ _ _ _ nn DISPLAY: Machine Model Number 14 - 9640, 9660, 9680
16 - 9540, 9560, 9580

 

OUZXMAG,00018A8 -19-10OCT02-9/9