E01 Header Control Unit

Diagnostic Addresses - E01 Header Control Unit

Control Unit Add. Line 2 Line 3 Description Details
Header E01 1 nnnn nn.nn Diagnostic Trouble Codes "none" - indicates there are no Diagnostic Trouble Codes.
"code" - indicates there are Diagnostic Trouble Codes available.
Push ENTER button to view codes. Use ARROW-UP and ARROW-DOWN to scroll through list of codes.
Header E01 2 _ _ _ _ nnnn BEEP: System The system will show the diagnostic address of any input that changes. Pushing the Enter Button will navigate to that address to display the status of that input.
Header E01 10 _ _ _ _ _ nn.n DISPLAY: Electronic Power (cc# 021) voltage. This is used to power the logic circuits of the control unit. Analog voltage shown in Volts DC. Battery Voltage
Header E01 11 _ _ _ _ nn.nn DISPLAY: CAN Lo (cc# 964) voltage Analog voltage shown in Volts DC
Header E01 12 _ _ _ _ nn.nn DISPLAY: CAN Hi (cc# 965) voltage Analog voltage shown in Volts DC
Header E01 13 _ _ _ _ _ nn.n DISPLAY: Control Circuit Power 2 (cc# 045) voltage to Header Control Unit at X205, Pin K3. This is used to power the valve driver circuits of the control unit. Analog voltage shown in Volts DC
Header E01 14 _ _ _ _ _nn.n DISPLAY: Control Circuit Power 2 (cc# 045) voltage to Header Control Unit at X205, Pin E3. This is used to power the reel valve driver circuits of the control unit. Analog voltage shown in Volts DC. Battery voltage. Engine must be running.
Header E01 15 _ _ _ _ _ n.nn DISPLAY: Height Sensor Power (cc# 481) voltage. This is used to power the HEADERTRAK Return to Cut Sensor and Header Height Sensors Analog voltage shown in Volts DC.
4.8 - 5.2 V is normal.
Header E01 16 _ _ _ _ _ n.nn DISPLAY: Height Sensor Power 2 (cc# 471) voltage. This is used to power the HEADERTRAK - Tilt Angle Sensor Analog voltage shown in Volts DC.
4.8 - 5.2 V is normal.
Header E01 17 _ _ _ _ nn.nn DISPLAY: Return to Cut Sensor (cc# 828) Analog voltage shown in Volts DC
Header E01 18 _ _ _ _ nn.nn DISPLAY: HEADERTRAK - Tilt Angle Sensor (cc# 833) Analog voltage shown in Volts DC
Header E01 19 _ _ _ _ nn.nn DISPLAY: Header Raise Pressure (cc# 706) Analog voltage shown in Volts DC
Header E01 20 _ _ _ _ nn.nn DISPLAY: Deck Plate Position Sensor or Reel Position Sensor (cc# 834) Analog voltage shown in Volts DC
Header E01 21 _ _ _ _ nn.nn DISPLAY: Reel Height Sensor (cc# 835) Analog voltage shown in Volts DC
Header E01 22 _ _ _ _ nn.nn DISPLAY: HEADERTRAK - Height Sensor 1 (Left) (cc# 412) Analog voltage shown in Volts DC

 

OUZXMAG,00018AF -19-10OCT02-1/12

Control Unit Add. Line 2 Line 3 Description Details
Header E01 24 _ _ _ _ nn.nn DISPLAY: HEADERTRAK - Height Sensor 3, Flex Height Sensor or DIAL-A-MATIC™ Pad #3 (cc# 414) Analog voltage shown in Volts DC
Header E01 25 _ _ _ _ nn.nn DISPLAY: HEADERTRAK - Height Sensor 4 or DIAL-A-MATIC™ Pad #6 (cc# 415) Analog voltage shown in Volts DC
Header E01 26 _ _ _ _ nn.nn DISPLAY: HEADERTRAK - Height Sensor 5 (Right) (cc# 454) Analog voltage shown in Volts DC
Header E01 27 _ _ _ _ nn.nn DISPLAY: Left ultrasonic sensor or DIAL-A-MATIC™ Pad #1 (cc# 416) Analog voltage shown in Volts DC
Header E01 28 _ _ _ _ nn.nn DISPLAY: Right ultrasonic sensor or DIAL-A-MATIC™ Pad #2 (cc# 417) Analog voltage shown in Volts DC
Header E01 40 _ _ _ _ nnnn DISPLAY: Reel Speed (cc# 608) Shown in Hertz
Header E01 50 _ _ _ _ nnxx DISPLAY: Header type indicated by select lines 0 = no header connected
2 = Row Crop Header w/ Contacting Height Sensors
3 = Row Crop w/ DIAL-A-MATIC™Sensor
4 = Corn Head w/ Contacting or Noncontacting Height Sensors
8 = Rigid Platform
12 = Flex Platform w/ Contacting Height Sensors
13 = Flex Platform w/ DIAL-A-MATIC™Sensor
Header E01 50 _ _ _ _ xxnn DISPLAY: Header type selected by controller 0 = no header connected
2 = Row Crop Header w/ Contacting Height Sensors
3 = Row Crop w/ DIAL-A-MATIC™Sensor
4 = Corn Head w/ Contacting or Noncontacting Height Sensors
8 = Rigid Platform
12 = Flex Platform w/ Contacting Height Sensors
13 = Flex Platform w/ DIAL-A-MATIC™Sensor
Header E01 51 _ _ _ _ _ nnn DISPLAY: Left ultrasonic digital value Range = 0 - 255
Header E01 52 _ _ _ _ _ nnn DISPLAY: Right ultrasonic digital value Range = 0 - 255
Header E01 53 _ _ _ 1 xxxx DISPLAY: DIAL-A-MATIC™Sensor inputs 1 = Pad 3 (header off ground) active
0 = Pad not active
3 = undefined input
Header E01 53 _ _ _ x 1xxx DISPLAY: DIAL-A-MATIC™Sensor inputs 1 = Pad 2 active
0 = Pad not active
3 = undefined input
Header E01 53 _ _ _ x x1xx DISPLAY: DIAL-A-MATIC™Sensor inputs 1 = Pad 1 active
0 = Pad not active
3 = undefined input
Header E01 53 _ _ _ x xx1x DISPLAY: DIAL-A-MATIC™Sensor inputs 1 = Pad 6 active
0 = Pad not active
3 = undefined input

 

DIAL-A-MATIC is a trademark of Deere & Company

OUZXMAG,00018AF -19-10OCT02-2/12

Control Unit Add. Line 2 Line 3 Description Details
Header E01 53 _ _ _ x xxx1 DISPLAY: DIAL-A-MATIC™Sensor inputs 1 = Pad 5 (header down hard on ground) active
0 = Pad not active
3 = undefined input
Header E01 60 _ _ 1x xxxx DISPLAY: CAN Bus message from Armrest Control Unit - Tilt Left Button 1 = message received that switch is pushed
0 = no message received or message received that switch is released
Header E01 60 _ _ x1 xxxx DISPLAY: CAN Bus message from Armrest Control Unit - Tilt Right Button 1 = message received that switch is pushed
0 = no message received or message received that switch is released
Header E01 60 _ _ xx 1xxx DISPLAY: CAN Bus message from Armrest Control Unit - Header Raise Fast Button 1 = message received that switch is pushed
0 = no message received or message received that switch is released
Header E01 60 _ _ xx x1xx DISPLAY: CAN Bus message from Armrest Control Unit - Header Raise Slow Button 1 = message received that switch is pushed
0 = no message received or message received that switch is released
Header E01 60 _ _ xx xx1x DISPLAY: CAN Bus message from Armrest Control Unit - Header Lower Fast Button 1 = message received that switch is pushed
0 = no message received or message received that switch is released
Header E01 60 _ _ xx xxx1 DISPLAY: CAN Bus message from Armrest Control Unit - Header Lower Slow Button 1 = message received that switch is pushed
0 = no message received or message received that switch is released
Header E01 61 _ _ _ _ 1xxx DISPLAY: CAN Bus message from Armrest Control Unit - Reel Fore Button 1 = message received that switch is pushed
0 = no message received or message received that switch is released
Header E01 61 _ _ _ _ x1xx DISPLAY: CAN Bus message from Armrest Control Unit - Reel Aft Button 1 = message received that switch is pushed
0 = no message received or message received that switch is released
Header E01 61 _ _ _ _ xx1x DISPLAY: CAN Bus message from Armrest Control Unit - Reel Raise Button 1 = message received that switch is pushed
0 = no message received or message received that switch is released
Header E01 61 _ _ _ _ xxx1 DISPLAY: CAN Bus message from Armrest Control Unit - Reel Lower Button 1 = message received that switch is pushed
0 = no message received or message received that switch is released
Header E01 62 _ _ _ _ 1xxx DISPLAY: CAN Bus message from Armrest Control Unit - Header Engaged 1 = message received that switch is pushed
0 = no message received or message received that switch is released
Header E01 62 _ _ _ _ x1xx DISPLAY: CAN Bus message from Armrest Control Unit - HEADERTRAK Activation Button 3 1 = message received that switch is pushed
0 = no message received or message received that switch is released
Header E01 62 _ _ _ _ xx1x DISPLAY: CAN Bus message from Armrest Control Unit - HEADERTRAK Activation Button 2 1 = message received that switch is pushed
0 = no message received or message received that switch is released
Header E01 62 _ _ _ _ xxx1 DISPLAY: CAN Bus message from Armrest Control Unit - HEADERTRAK Activation Button 1 1 = message received that switch is pushed
0 = no message received or message received that switch is released

 

DIAL-A-MATIC is a trademark of Deere & Company

OUZXMAG,00018AF -19-10OCT02-3/12

Control Unit Add. Line 2 Line 3 Description Details
Header E01 63 _ _ 1x xxxx DISPLAY: CAN Bus message from Armrest Control Unit - HYDRAFLEX™Pressure Increase Button 1 = message received that switch is pushed
0 = no message received or message received that switch is released
Header E01 63 _ _ x1 xxxx DISPLAY: CAN Bus message from Armrest Control Unit - HYDRAFLEX™Pressure Decrease Button 1 = message received that switch is pushed
0 = no message received or message received that switch is released
Header E01 63 _ _ xx 1xxx DISPLAY: CAN Bus message from Armrest Control Unit - Reel Speed Increase Button 1 = message received that switch is pushed
0 = no message received or message received that switch is released
Header E01 63 _ _ xx x1xx DISPLAY: CAN Bus message from Armrest Control Unit - Reel Speed Decrease Button 1 = message received that switch is pushed
0 = no message received or message received that switch is released
Header E01 63 _ _ xx xx1x DISPLAY: CAN Bus message from Armrest Control Unit - Road/Field Status 1 = message received that combine is in Road mode
0 = no message received or message received that combine is in Field mode
Header E01 63 _ _ xx xxx1 DISPLAY: CAN Bus message from Armrest Control Unit - Dump Valve Request 1 = message received that dump valve activation is requested
0 = no message received or message received that dump valve request is cancelled
Header E01 64 _ _ _ _ _ nnn DISPLAY: CAN Bus message from Armrest Control Unit - HEADERTRAK Height Encoder value Clockwise rotation increases value. Counterclockwise rotation decreases value.
Range = 0 - 255
Header E01 65 _ _ _ _ _ nnn DISPLAY: CAN Bus message from Armrest Control Unit - HEADERTRAK Sensitivity Adjust setting Clockwise rotation increases value. Counterclockwise rotation decreases value.
Range = 0 - 100
Header E01 66 _ _ _ _ _ nnn DISPLAY: CAN Bus message from Armrest Control Unit - HEADERTRAK Rate Adjust setting Clockwise rotation increases value. Counterclockwise rotation decreases value
Range = 0 - 100
Header E01 67 _ _ _ _ _ nnn DISPLAY: CAN Bus message from Armrest Control Unit - DIAL-A-SPEED Encoder value Clockwise rotation increases value. Counterclockwise rotation decreases value.
Range = 0 - 11
0 = minimum reel speed
11 = maximum reel speed
Header E01 70 _ _ _ _ 1xxx DISPLAY: CAN Bus message from Cornerpost Control Unit - header lift valve type 1 = Proportional Valve
Header E01 70 _ _ _ _ x1xx DISPLAY: CAN Bus message from Cornerpost Control Unit - header lift valves 1 = two valves
Header E01 70 _ _ _ _ xx1x DISPLAY: CAN Bus message from Cornerpost Control Unit - reel lift valve type 1 = separate reel lift and reel lower valves
0 = single reel height valve
Header E01 70 _ _ _ _ xxx1 DISPLAY: CAN Bus message from Cornerpost Control Unit - measurement units 1 = metric units
0 = English units
Header E01 71 _ _ _ 1 xxxx DISPLAY: CAN Bus message from Cornerpost Control Unit - Option Availability - HEADERTRAK - Stubble Height 1 = option is installed
0 = option is not installed.

 

HYDRAFLEX is a trademark of Deere & Company

OUZXMAG,00018AF -19-10OCT02-4/12

Control Unit Add. Line 2 Line 3 Description Details
Header E01 71 _ _ _ x 1xxx DISPLAY: CAN Bus message from Cornerpost Control Unit - Option Availability - HEADERTRAK - Tilt 1 = option is installed
0 = option is not installed.
Header E01 71 _ _ _ x x1xx DISPLAY: CAN Bus message from Cornerpost Control Unit - Option Availability - HEADERTRAK - Ground Pressure 1 = option is installed
0 = option is not installed.
Header E01 71 _ _ _ x xx1x DISPLAY: CAN Bus message from Cornerpost Control Unit - Option Availability - Reel Resume 1 = option is installed
0 = option is not installed.
Header E01 71 _ _ _ x xxx1 DISPLAY: CAN Bus message from Cornerpost Control Unit - Option Availability - DIAL-A-SPEED 1 = option is installed
0 = option is not installed.
Header E01 72 _ _ 1x xxxx DISPLAY: CAN Bus message from Cornerpost Control Unit - HEADERTRAK - Stubble Height Enabled 1 = enabled
0 = no message received or message received that option is not enabled
Header E01 72 _ _ x1 xxxx DISPLAY: CAN Bus message from Cornerpost Control Unit - Header Flotation enabled 1 = enabled
0 = no message received or message received that option is not enabled
Header E01 72 _ _ xx 1xxx DISPLAY: CAN Bus message from Cornerpost Control Unit - HEADERTRAK - Tilt enabled 1 = enabled
0 = no message received or message received that option is not enabled
Header E01 72 _ _ xx x1xx DISPLAY: CAN Bus message from Cornerpost Control Unit - HEADERTRAK - Stubble Height enabled 1 = enabled
0 = no message received or message received that option is not enabled
Header E01 72 _ _xx xx1x DISPLAY: CAN Bus message from Cornerpost Control Unit - Reel Resume enabled 1 = enabled
0 = no message received or message received that option is not enabled
Header E01 72 _ _xx xx1x DISPLAY: CAN Bus message from Cornerpost Control Unit - DIAL-A-SPEED enabled 1 = enabled
0 = no message received or message received that option is not enabled
Header E01 73 _ _ _ _ nnn.n DISPLAY: CAN Bus message from Engine Control Unit - Engine Speed rpm
Header E01 74 _ _ _ _ _ nn.n DISPLAY: CAN Bus message from Left Control Unit - Ground Speed Miles per hour or Kilometers per hour
Header E01 75 _ _ _ _ _ nn.n DISPLAY: Reel Speed Miles per hour or Kilometers per hour
Header E01 100 _ _ _ _ _ _ _ _ CALIBRATION: Factory Interactive Calibration Mode  
Header E01 101 _ _ _ _ _ _ _ _ CALIBRATION: Header Interactive Calibration Mode  
Header E01 102 _ _ _ _ _ _ _ _ CALIBRATION: HEADERTRAK - Tilt Interactive Calibration Mode  
Header E01 103 _ _ _ _ _ _ _ _ CALIBRATION: HEADERTRAK - Ground Pressure Interactive Calibration Mode  
Header E01 104 _ _ _ _ _ _ _ _ CALIBRATION: Adjustable Deck Plate Interactive Calibration Mode  

 

OUZXMAG,00018AF -19-10OCT02-5/12

Control Unit Add. Line 2 Line 3 Description Details
Header E01 110 _ _ _ _ _ n.nn DISPLAY/MODIFY: Manual header raise time to disable HEADERTRAK features. Not modifiable when engine is running. Shown in seconds.
Range = 0.50 - 2.50
Default = 1.50
Header E01 111 _ _ _ _ _ nnn DISPLAY/MODIFY: Deadband for HEADERTRAK - Tilt algorithm. Not modifiable when engine is running. Range = 50 - 250
Default = 150
Header E01 112 _ _ _ _ _ nnn DISPLAY/MODIFY: Deadband for HEADERTRAK - Stubble Height algorithm. Not modifiable when engine is running. Range = 50 - 250
Default = 105
Header E01 113 _ _ _ _ _ nnn DISPLAY/MODIFY: Deadband for HEADERTRAK - Return to Cut algorithm. Not modifiable when engine is running. Range = 50 - 250
Default = 90
Header E01 114 _ _ _ _ _ nnn DISPLAY/MODIFY: Threshold for Drop Rate Valve Range = 50 - 250
Default = 100
Header E01 115 _ _ _ _ _ nnn DISPLAY/MODIFY: Gain for HEADERTRAK - Tilt algorithm Increase number to slow response of HEADERTRAK - Tilt to changes
Range = 2-8
Default = 6
Header E01 116 _ _ _ _ _ nnn DISPLAY/MODIFY: HEADERTRAK - Return to Cut display range Range = 0 - 3000 mm or 0 - 99.9 inches
Default = set by header type
Header E01 117 _ _ _ _ _ nnn DISPLAY/MODIFY: HEADERTRAK - Stubble Height display range Range = 0 - 3000 mm or 0 - 99.9 inches
Default = set by header type
Header E01 118 _ _ _ _ _ nnn DISPLAY/MODIFY: Ultrasonic Sensor offset Number adjusts the level position of the header when HEADERTRAK - Tilt is using Non-Contacting Sensors (Ultrasonic).
To lower left end - decrease number.
To lower right end - increase number
Range = 0 - 100
Default = 50 (no offset)
Header E01 119 _ _ _ _ nnnn DISPLAY/MODIFY: DIAL-A-SPEED transfer function Ratio of reel speed frequency to reel tip velocity
Range = 1200 - 2200
Default = 1892
Header E01 120 _ _ _ _ _ nnn DISPLAY/MODIFY: Minimum reel speed for DIAL-A-SPEED Range = 1.6 - 5.0 km/h or 1.0 - 3.2 mph
Header E01 121 _ _ _ _ _ nnn DISPLAY/MODIFY: Maximum reel speed for DIAL-A-SPEED Range = 8.0 - 16.0 km/h or 5.0 - 10.0 mph
Header E01 122 _ _ _ _ _ nnn DISPLAY/MODIFY: Select DIAL-A-SPEED numerical display on Cornerpost Display Unit 3 1 = display Reel Speed to Ground Speed offset in km/h or mph. The offset is operator adjustable with the DIAL-A-SPEED Encoder
0 = display Reel Speed to Ground Speed as ratio. The ratio is operator adjustable with the DIAL-A-SPEED Encoder
Default = 0
Header E01 123 _ _ _ _ _ nnn DISPLAY/MODIFY: Cutterbar height setpoint for HEADERTRAK - Ground Pressure Range = 0 - 250
Default = 35
Header E01 124 _ _ _ _ _ _ _ n DISPLAY/MODIFY: Activation Button 2 operation mode select 0 = HEADERTRAK - Stubble Height
1 = HEADERTRAK - Return to Cut

 

OUZXMAG,00018AF -19-10OCT02-6/12

Control Unit Add. Line 2 Line 3 Description Details
Header E01 125 _ _ _ _ nnnn CALIBRATION: Header Width Range for cutting platforms = 0 - 60 meters or 0 - 200 feet
Range for row crop or corn heads = 0 - 9999 mm or 0 - 2400 inches
Header E01 126 _ _ _ _ _ nnn DISPLAY/MODIFY: DIAL-A-SPEED algorithm deadband Range = 50 - 250
Default = 128
Header E01 127 _ _ _ _ _ _ _ n DISPLAY/MODIFY: Header Fast Raise for HYDRAFLEX Platforms only 1 = Slow and Fast Raise will be used as required by HEADERTRAK - Stubble Height
0 = only Fast Raise will be used by HEADERTRAK - Stubble Height
Header E01 128 _ _ _ _ _ nnn DISPLAY/MODIFY: Height valve command - algorithm gain Increase number to increase reaction
Decrease number to increase system stability
Range = 50 - 250
Default = 120
Header E01 129 _ _ _ _ _ _ _ n DISPLAY/MODIFY: HEADERTRAK Ground Pressure algorithm gain Increase number to increase reaction
Decrease number to increase system stability
Range = 1 - 5
Default = 3
Header E01 130 _ _ _ _ _ nxx DISPLAY: Height valve command - direction 0 = Output off
1 = Raise
2 = Lower
Header E01 130 _ _ _ _ _ xnn DISPLAY: Height valve command - speed Shown in percent
Range = 0 - 99
Header E01 131 _ 1xx xxxx DISPLAY: Tilt Left Valve command 1 = output to valve turned on
0 = Output off
Header E01 131 _ x1x xxxx DISPLAY: Tilt Right Valve command 1 = output to valve turned on
0 = Output off
Header E01 131 _ xx1 xxxx DISPLAY: Dump Valve command 1 = output to valve turned on
0 = Output off
Header E01 131 _ xxx 1xxx DISPLAY: Reel Fore Valve command 1 = output to valve turned on
0 = Output off
Header E01 131 _ xxx x1xx DISPLAY: Reel Aft Valve command 1 = output to valve turned on
0 = Output off
Header E01 131 _ xxx xx1x DISPLAY: Reel Raise Valve command (used with Dump Valve Command) 1 = output to valve turned on
0 = Output off
Header E01 131 _ xxx xxx1 DISPLAY: Reel Lower Valve command 1 = Output to valve turned on
0 = Output off
Header E01 132 _ _ _ _ _ 1xx DISPLAY: HYDRAFLEX Pressure Select Valve command 1 = Output to valve turned on
0 = Output off
Header E01 132 _ _ _ _ _ x1x DISPLAY: Accumulator Shutoff Valve command 1 = Output to valve turned on
0 = Output off
Header E01 132 _ _ _ _ _ xx1 DISPLAY: Header Drop Rate Valve command 1 = Output to valve turned on
0 = Output off
Header E01 133 _ _ _ _ _ nxx DISPLAY: Reel speed motor command - direction 0 = motor off
1 = increasing
2 = decreasing

 

OUZXMAG,00018AF -19-10OCT02-7/12

Control Unit Add. Line 2 Line 3 Description Details
Header E01 133 _ _ _ _ _ xnn DISPLAY: Reel speed motor command - speed Shown in percent
Range = 0 - 99
Header E01 140 _ _ _ 1 xxxx DISPLAY: Flex Height Sensor 1 = HEADERTRAK System recognizes sensors due to input from sensors greater than 0.5 V DC
0 = HEADERTRAK System does not recognize sensors due to input from sensors less than 0.5 V DC
Header E01 140 _ _ _ x 1xxx DISPLAY: Non-Contacting Height Sensors (Ultrasonic) 1 = HEADERTRAK System recognizes sensors due to digital data stream from sensors
0 = HEADERTRAK System does not recognize sensors due to lack of digital data stream from sensors.
Header E01 140 _ _ _ x x1xx DISPLAY: Deck Plate Spacing Sensor 1 = HEADERTRAK System recognizes sensors due to input from sensors greater than 0.5 V DC
0 = HEADERTRAK System does not recognize sensors due to input from sensors less than 0.5 V DC
Header E01 140 _ _ _ x xx1x DISPLAY: Center HEADERTRAK - Height Sensor 1 = HEADERTRAK System recognizes sensors due to input from sensors greater than 0.5 V DC
0 = HEADERTRAK System does not recognize sensors due to input from sensors less than 0.5 V DC
Header E01 140 _ _ _ x xxx1 DISPLAY: Contacting HEADERTRAK - Height Sensors 1 = HEADERTRAK System recognizes sensors due to input from sensors greater than 0.5 V DC
0 = HEADERTRAK System does not recognize sensors due to input from sensors less than 0.5 V DC
Header E01 141 _ _ _ n xxxx DISPLAY: Height Sensor Override. Height sensor override will prevent a header from hitting the ground while in the return-to-cut mode by automatically raising the header whenever the height sensors touch the ground. 0 = normal
1 = override
Header E01 141 _ _ _ x nxxx DISPLAY: Harvesting status. Machine harvesting status based on an operator adjustable feeder house angle threshold. When the feeder house is below the threshold, the machine is harvesting, and when the feeder house is above the threshold, the machine is not harvesting. 0 = not harvesting
1 = harvesting
Header E01 141 _ _ _ x xnxx DISPLAY: HEADERTRAK - Tilt operating mode 0 = Off
2 = Manual tilt right
3 = Manual tilt left
4 = Automatic tilt mode
5 = Automatic tilt mode with ultrasonics

 

OUZXMAG,00018AF -19-10OCT02-8/12

Control Unit Add. Line 2 Line 3 Description Details
Header E01 141 _ _ _ x xxnn DISPLAY: Height Control operating mode 0 = Off
1 = Open loop enable mode
2 = Open loop slow raise mode
3 = Open loop slow lower mode
4 = Open loop fast raise mode
5 = Open loop fast lower mode
6 = Manual enable mode
7 = Manual slow raise mode
8 = Manual slow lower mode
9 = Manual fast raise mode
10 = Manual fast lower mode
11 = HEADERTRAK Return to Cut enable mode
12 = HEADERTRAK Stubble Height initial mode
13 = HEADERTRAK Stubble Height enable mode
14 = HEADERTRAK - Ground Pressure initial mode
15 = HEADERTRAK - Ground Pressure enable mode
16 = Open loop slow lower override mode
17 = Open loop slow raise override mode
Header E01 142 _ _ _ _ nxxx DISPLAY: Header Flotation operating mode 0 = HEADERTRAK - Ground Pressure disabled
1 = Manual HEADERTRAK - Ground Pressure Enable
2 = Manual HEADERTRAK - Ground Pressure Increase
3 = Manual HEADERTRAK - Ground Pressure Decrease
6 = HEADERTRAK - Ground Pressure - Activation Button 1
7 = HEADERTRAK - Ground Pressure - Activation Button 2
8 = HEADERTRAK - Ground Pressure - Activation Button 3
Header E01 142 _ _ _ _ xnxx DISPLAY: DIAL-A-SPEED operating mode 0 = DIAL-A-SPEED disabled
1 = Manual Enable
2 = Manual Speed Increase
3 = Manual Speed Decrease
Header E01 142 _ _ _ _ xxnx DISPLAY: Reel Resume - Fore/Aft operating mode 0 = disabled
1 = Manual Enable
2 = Manual Reel Fore
3 = Manual Reel Aft
6 = Reel Resume - Activation Button 1
7 = Reel Resume - Activation Button 2
8 = Reel Resume - Activation Button 3

 

OUZXMAG,00018AF -19-10OCT02-9/12

Control Unit Add. Line 2 Line 3 Description Details
Header E01 142 _ _ _ _ xxxn DISPLAY: Reel Resume - Raise/Lower operating mode 0 = off
1 = Manual Enable
4 = Manual Reel Raise
5 = Manual Reel Lower
6 = Reel Resume - Activation Button 1
7 = Reel Resume - Activation Button 2
8 = Reel Resume - Activation Button 3
Header E01 143 _ _ _ n nnnn DISPLAY: Failure overriding modes. This number is the sum of all failure modes existing at once. 0 = Normal
1 = Shut off raise/lower valves due to valve driver problems
2 = Shut off tilt valves
4 = No HEADERTRAK - Stubble Height
8 = No HEADERTRAK - Stubble Height, Ground Pressure, or Height Resume
16 = No HEADERTRAK - Stubble Height
32 = No HEADERTRAK - Ground Pressure
64 = No HEADERTRAK - Tilt
128 = No HEADERTRAK - Tilt with non-contacting (ultrasonic) sensors
256 = No Reel Resume Raise/Lower for Activation Button 1
512 = No Reel Resume Fore/Aft for Activation Button 1
1024 = No Reel Resume Raise/Lower for Activation Button 2
2048 = No Reel Resume Fore/Aft for Activation Button 2
4096 = No Reel Resume Raise/Lower for Activation Button 3
8192 = No Reel Resume Fore/Aft for Activation Button 3
Header E01 144 _ _ _ _ _ nnn DISPLAY: Feeder House position command Command by controller
Range = 0 - 127
Header E01 145 _ _ _ _ _ nnn DISPLAY: Position set point Set by rotating Height Control Encoder
Range = 0 - 127
Header E01 146 _ _ _ _ _ nnn DISPLAY: Feeder House position Input from HEADERTRAK Return to Cut Sensor
Range = 0 - 127
Header E01 147 _ _ _ _ _ nnn DISPLAY: HEADERTRAK - Height Input from HEADERTRAK - Height Sensor
Range = 0 - 127
Header E01 148 _ _ _ _ _ nnn DISPLAY: Header tilt position (left - right) from HEADERTRAK - Tilt Sensor Input from HEADERTRAK - Tilt Sensor
0 = level
As the right end goes down the number increases from 0 towards 127
As the left end goes down, the numbers decrease from 255 towards 128
(Left Down) 128 - - 191 - - 255/0 - - 63 - - 127 (Right Down)

 

OUZXMAG,00018AF -19-10OCT02-10/12

Control Unit Add. Line 2 Line 3 Description Details
Header E01 149 _ _ _ _ _ nnn DISPLAY: Header tilt position (left - right) from Non-Contacting HEADERTRAK - Height Sensor (Ultrasonic) Input from Non-Contacting HEADERTRAK - Height Sensor (Ultrasonic)
0 = level
As the right end goes down the number increases from 0 towards 127
As the left end goes down, the numbers decrease from 255 towards 128
(Left Down) 128 - - 191 - - 255/0 - - 63 - - 127 (Right Down)
Header E01 150 nnnn xxxx DISPLAY: Header raise valve current Shown in milliamperes.
Range = 0 - 3400
Header E01 150 xxxx nnnn DISPLAY: Header lower valve current Shown in milliamperes.
Range = 0 - 3400
Header E01 151 _ _ _ _ _ nnn DISPLAY: Lift cylinder pressure Shown in bar
(kPa = bar x 100)
(PSI = bar / 0.06894)
Header E01 152 _ _ _ n nnnn DISPLAY: calibrated header types List of calibrated headers by type. Rotate encoder to scroll through list. Top line of display is header number. Bottom line of display is header type.
0 = n/a
1 = n/a
2 = Row Crop Header w/ Contacting Height Sensors
3 = Row Crop
4 = Corn Head w/ Contacting Height Sensors
5 = n/a
8 = Rigid Platform
9 = n/a
11 = n/a
12 = Flex Platform w/ Contacting Height Sensors
13 = Flex Platform w/ DIAL-A-MATIC™Sensor
14 = no header connected
15 = n/a
Header E01 157 _ _ _ _ nnnn DISPLAY: HYDRAFLEX Pressure Shown in bar
(kPa = bar x 100)
(PSI = bar / 0.06894)
Header E01 227 _ _ nn nnnn DISPLAY: Part number of the boot block program  
Header E01 228 _ _ _ _ _ nn.n DISPLAY: Version number of the boot block program  
Header E01 233 _ _ nn nnnn DISPLAY: Base program part number  
Header E01 234 _ _ _ _ nnn.n DISPLAY: Base program version number  
Header E01 235 _ _ nn nnnn DISPLAY: Device part number  

 

DIAL-A-MATIC is a trademark of Deere & Company

OUZXMAG,00018AF -19-10OCT02-11/12

Control Unit Add. Line 2 Line 3 Description Details
Header E01 236 nnnn nnnn DISPLAY: Device serial number  
Header E01 247 _ _ _ _ _ _ nn DISPLAY: Machine Model Number 14 = 9640, 9660, 9680
16 = 9540, 9560, 9580

 

OUZXMAG,00018AF -19-10OCT02-12/12