E03 Left Control Unit

Diagnostic Addresses - E03 Left Control Unit

Control Unit Add. Line 2 Line 3 Description Details
Left E03 1 nnnn nn.nn Diagnostic Trouble Codes "none" - indicates there are no Diagnostic Trouble Codes.
"code" - indicates there are Diagnostic Trouble Codes available.
Push ENTER button to view codes. Use ARROW-UP and ARROW-DOWN to scroll through list of codes.
Left E03 2 _ _ _ _ nnnn BEEP: System Beep Mode The system will show the diagnostic address of any input that changes. Pushing the Enter Button will navigate to that address to display the status of that input.
Left E03 3 _ _ _ _ nnnn BEEP: Analog Beep Mode The system will show the diagnostic address of any analog input that changes. Pushing the Enter Button will navigate to that address to display the status of that input.
Left E03 4 _ _ _ _ nnnn BEEP: Frequency Beep Mode The system will show the diagnostic address of any frequency input that changes. Pushing the Enter Button will navigate to that address to display the status of that input.
Left E03 5 _ _ _ _ nnnn BEEP: Digital Beep Mode The system will show the diagnostic address of any digital input that changes. Pushing the Enter Button will navigate to that address to display the status of that input.
Left E03 10 _ _ _ _ nn.nn DISPLAY: Left Control Unit Power (cc# 027) voltage Analog voltage shown in Volts DC
Left E03 11 _ _ _ _ nn.nn DISPLAY: CAN Hi (cc# 965) voltage Analog voltage shown in Volts DC
Left E03 12 _ _ _ _ nn.nn DISPLAY: CAN Lo (cc# 964) voltage Analog voltage shown in Volts DC
Left E03 13 _ _ _ _ nn.nn DISPLAY: +5V reference voltage Analog voltage shown in Volts DC
Left E03 14 _ _ _ _ nn.nn DISPLAY: Unswitched Electronic Power (cc# 022) voltage Analog voltage shown in Volts DC
Left E03 15 _ _ _ _ nn.nn DISPLAY: Light Power 2 (cc# 046) voltage Analog voltage shown in Volts DC
Left E03 20 _ _ _ _ nnnn DISPLAY: Ground Speed Shown in Hertz
Left E03 21 _ _ _ _ nnnn DISPLAY: Backshaft Speed Shown in Hertz
Left E03 30 1xxx xxxx DISPLAY: CAN Bus message from Left Control Unit 2 - Concave (Threshing) Clearance increase 1 = increase request
0 = off
3 = undefined
Left E03 30 x1xx xxxx DISPLAY: CAN Bus message from Left Control Unit 2 - Concave (Threshing) Clearance decrease 1 = decrease request
0 = off
3 = undefined
Left E03 30 xx1x xxxx DISPLAY: CAN Bus message from Armrest Control Unit - Concave (Threshing) Clearance Increase Button 1 = button pressed
0 = button released
3 = message not received

 

OUZXMAG,00018B2 -19-10OCT02-1/15

Control Unit Add. Line 2 Line 3 Description Details
Left E03 30 xxx1 xxxx DISPLAY: CAN Bus message from Armrest Control Unit - Concave (Threshing) Clearance Decrease Button 1 = button pressed
0 = button released
3 = message not received
Left E03 30 xxxx 1xxx DISPLAY: Concave (Threshing) Clearance Increase relay output from Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 30 xxxx x1xx DISPLAY: Concave (Threshing) Clearance Decrease relay output from Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 30 xxxx xx1x DISPLAY: Concave (Threshing) Clearance Increase command to Relay Control Board 1 = on
0 = off
3 = undefined
Left E03 30 xxxx xxx1 DISPLAY: Concave (Threshing) Clearance Decrease command to Relay Control Board 1 = on
0 = off
3 = undefined
Left E03 31 1xxx xxxx DISPLAY: CAN Bus message from Left Control Unit 2 - Cleaning Fan Speed increase 1 = increase request
0 = off
3 = undefined
Left E03 31 x1xx xxxx DISPLAY: CAN Bus message from Left Control Unit 2 - Cleaning Fan Speed decrease 1 = decrease request
0 = off
3 = undefined
Left E03 31 xx1x xxxx DISPLAY: CAN Bus message from Armrest Control Unit - Cleaning Fan Speed Increase Button 1 = button pressed
0 = button released
3 = message not received
Left E03 31 xxx1 xxxx DISPLAY: CAN Bus message from Armrest Control Unit - Cleaning Fan Speed Decrease Button 1 = button pressed
0 = button released
3 = message not received
Left E03 31 xxxx 1xxx DISPLAY: Cleaning Fan Speed Increase relay output from Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 31 xxxx x1xx DISPLAY: Cleaning Fan Speed Decrease relay output from Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 31 xxxx xx1x DISPLAY: Cleaning Fan Speed Increase command to Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 31 xxxx xxx1 DISPLAY: Cleaning Fan Speed Decrease command to Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 32 xx1x xxxx DISPLAY: CAN Bus message from Armrest Control Unit - Vane Angle Left Button 1 = button pressed
0 = button released
3 = message not received
Left E03 32 xxx1 xxxx DISPLAY: CAN Bus message from Armrest Control Unit - Vane Angle Right Button 1 = button pressed
0 = button released
3 = message not received
Left E03 32 xxxx 1xxx DISPLAY: Vane Angle Left relay output from Control Relay Board 1 = on
0 = off
3 = undefined

 

OUZXMAG,00018B2 -19-10OCT02-2/15

Control Unit Add. Line 2 Line 3 Description Details
Left E03 32 xxxx x1xx DISPLAY: Vane Angle Right relay output from Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 32 xxxx xx1x DISPLAY: Vane Angle Left command to Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 32 xxxx xxx1 DISPLAY: Vane Angle Right command to Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 33 1xxx xxxx DISPLAY: CAN Bus message from Left Control Unit 2 - Cylinder (Threshing) Speed increase 1 = increase request
0 = off
3 = undefined
Left E03 33 x1xx xxxx DISPLAY: CAN Bus message from Left Control Unit 2 - Cylinder (Threshing) Speed decrease 1 = decrease request
0 = off
3 = undefined
Left E03 33 xx1x xxxx DISPLAY: CAN Bus message from Armrest Control Unit - Cylinder (Threshing) Speed Increase Button 1 = button pressed
0 = button released
3 = message not received
Left E03 33 xxx1 xxxx DISPLAY: CAN Bus message from Armrest Control Unit - Cylinder (Threshing) Decrease Button 1 = button pressed
0 = button released
3 = message not received
Left E03 33 xxxx xx1x DISPLAY: Cylinder (Threshing) Speed Increase driver status 1 = Output normal
0 = Output shorted or open
Left E03 33 xxxx xxx1 DISPLAY: Cylinder (Threshing) Speed change command to driver 1 = on
0 = off
3 = undefined
Left E03 34 xxx1 xxxx DISPLAY: Draper Speed driver status 1 = Output normal
0 = Output shorted or open
Left E03 34 xxxx 1xxx DISPLAY: CAN Bus message from Armrest Control Unit - Draper Speed Increase Button 1 = button pressed
0 = button released
3 = message not received
Left E03 34 xxxx x1xx DISPLAY: CAN Bus message from Armrest Control Unit - Draper Speed Decrease Button 1 = button pressed
0 = button released
3 = message not received
Left E03 34 xxxx xx1x DISPLAY: Draper Speed Increase command to driver 1 = on
0 = off
3 = undefined
Left E03 34 xxxx xxx1 DISPLAY: Draper Speed Decrease command to driver 1 = on
0 = off
3 = undefined
Left E03 35 xxx1 xxxx DISPLAY: CAN Bus message from Armrest Control Unit - CLIMATRAK compressor clutch engage 1 = engage request
0 = off
3 = undefined
Left E03 35 xxxx x1xx DISPLAY: CLIMATRAK High Pressure Switch 1 = switch closed
0 = switch open
3 = undefined
Left E03 35 xxxx xx1x DISPLAY: CLIMATRAK Compressor Clutch driver status 1 = Output normal
0 = Output shorted or open

 

OUZXMAG,00018B2 -19-10OCT02-3/15

Control Unit Add. Line 2 Line 3 Description Details
Left E03 35 xxxx xxx1 DISPLAY: CLIMATRAK Compressor Clutch command to driver 1 = on
0 = off
3 = undefined
Left E03 36 1xxx xxxx DISPLAY: CAN Bus message from Armrest Control Unit - Auger Swing Out Automatic Button 1 = button pressed
0 = button released
3 = message not received
Left E03 36 x1xx xxxx DISPLAY: CAN Bus message from Armrest Control Unit - Auger Swing Out Manual Button 1 = button pressed
0 = button released
3 = message not received
Left E03 36 xx1x xxxx DISPLAY: CAN Bus message from Armrest Control Unit - Auger Swing In Automatic Button 1 = button pressed
0 = button released
3 = message not received
Left E03 36 xxx1 xxxx DISPLAY: CAN Bus message from Armrest Control Unit - Auger Swing In Manual Button 1 = button pressed
0 = button released
3 = message not received
Left E03 36 xxxx x1xx DISPLAY: Auger Swing driver status 1 = Output normal
0 = Output shorted or open
Left E03 36 xxxx xx1x DISPLAY: Auger Swing Out command to driver 1 = on
0 = off
3 = undefined
Left E03 36 xxxx xxx1 DISPLAY: Auger Swing In command to driver 1 = on
0 = off
3 = undefined
Left E03 37 x1xx xxxx DISPLAY: Auger Auto Swing In mode 1 = off
0 = engaged
3 = undefined
Left E03 37 xx1x xxxx DISPLAY: CAN Bus message from Armrest Control Unit - Quick Stop Button 1 = button released
0 = button pressed
3 = undefined
Left E03 37 xxx1 xxxx DISPLAY: Message from Control Relay Board - Key Switch 1 = START
0 = OFF, ACCESSORY or RUN
Left E03 37 xxxx 1xxx DISPLAY: CAN Bus message from Armrest Control Unit - Road/Field Button 0 = ROAD
1 = FIELD
Left E03 37 xxxx x1xx DISPLAY: Auger Engage driver status 1 = Output normal
0 = Output shorted or open
Left E03 37 xxxx xx1x DISPLAY: CAN Bus message from Armrest Control Unit - Auger Engage Button 1 = button pressed
0 = button released
3 = message not received
Left E03 37 xxxx xxx1 DISPLAY: Auger Engage command to driver 1 = on
0 = off
3 = undefined
Left E03 38 1xxx xxxx DISPLAY: Left High Speed Four Wheel Drive driver status 1 = Output normal
0 = Output shorted or open
Left E03 38 x1xx xxxx DISPLAY: Right High Speed Four Wheel Drive driver status 1 = Output normal
0 = Output shorted or open
Left E03 38 xx1x xxxx DISPLAY: CAN Bus message from Armrest Control Unit - High Speed Four Wheel Drive Button 1 = button pressed
0 = button released
3 = message not received

 

OUZXMAG,00018B2 -19-10OCT02-4/15

Control Unit Add. Line 2 Line 3 Description Details
Left E03 38 xxx1 xxxx DISPLAY: CAN Bus message from Armrest Control Unit - Low Speed Four Wheel Drive Button 1 = button pressed
0 = button released or message not received
3 = undefined
Left E03 38 xxxx 1xxx DISPLAY: Left High Speed Four Wheel Drive command to driver 1 = on
0 = off
3 = undefined
Left E03 38 xxxx x1xx DISPLAY: Right High Speed Four Wheel Drive command to driver 1 = on
0 = off
3 = undefined
Left E03 38 xxxx xx1x DISPLAY: Low Speed Four Wheel Drive driver status 1 = Output normal
0 = Output shorted or open
Left E03 38 xxxx xxx1 DISPLAY: Low Speed Four Wheel Drive command to driver 1 = on
0 = off
3 = undefined
Left E03 39 x1xx xxxx DISPLAY: Message from Control Relay Board - Key Switch Start 1 = START
0 = OFF, ACCESSORY or RUN
3 = undefined
Left E03 39 xx1x xxxx DISPLAY: OK to Start relay output from Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 39 xxx1 xxxx DISPLAY: CAN Bus message from Engine Control Unit - Engine Speed 1 = Less than 1100 rpm
0 = Greater than 1100 rpm
Left E03 39 xxxx 1xxx DISPLAY: CAN Bus message from Armrest Control Unit - Header Engage Switch 1 = DISENGAGED
0 = ENGAGED
3 = message not received
Left E03 39 xxxx x1xx DISPLAY: CAN Bus message from Armrest Control Unit - Separator Engage Switch 1 = DISENGAGED
0 = ENGAGED
3 = message not received
Left E03 39 xxxx xx1x DISPLAY: CAN Bus message from Armrest Control Unit - Multifunction Lever 1 = Neutral
0 = Out of Neutral
3 = message not received
Left E03 39 xxxx xxx1 DISPLAY: OK to Start command to Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 40 xxx1 xxxx DISPLAY: Auger Engage command to Control Relay Board 1 = off
0 = on
3 = undefined
Left E03 40 xxxx 1xxx DISPLAY: Auger Swing Out command to Control Relay Board 1 = off
0 = on
3 = undefined
Left E03 40 xxxx x1xx DISPLAY: Auger Swing In command to Control Relay Board 1 = off
0 = on
3 = undefined
Left E03 40 xxxx xx1x DISPLAY: Start Signal "Neutral Switched" 1 = on
0 = off
3 = undefined

 

OUZXMAG,00018B2 -19-10OCT02-5/15

Control Unit Add. Line 2 Line 3 Description Details
Left E03 40 xxxx xxx1 DISPLAY: OK to Start command to Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 41 xxxx 1xxx DISPLAY: CAN Bus message from Armrest Control Unit - Hillmaster Tilt Left Button 1 = button pressed
0 = button released
3 = message not received
Left E03 41 xxxx x1xx DISPLAY: CAN Bus message from Armrest Control Unit - Hillmaster Tilt Right Button 1 = button pressed
0 = button released
3 = message not received
Left E03 41 xxxx xx1x DISPLAY: Hillmaster Tilt Left command to driver 1 = on
0 = off
3 = undefined
Left E03 41 xxxx xxx1 DISPLAY: Hillmaster Tilt Right command to driver 1 = on
0 = off
3 = undefined
Left E03 42 xxx1 xxxx DISPLAY: CAN Bus message from Armrest Control Unit - Hillmaster Engage Button 1 = button pressed
0 = button released
3 = message not received
Left E03 42 xxxx 1xxx DISPLAY: Combine Lower driver status 1 = Output normal
0 = Output shorted or open
Left E03 42 xxxx x1xx DISPLAY: Hillmaster Engage driver status 1 = Output normal
0 = Output shorted or open
Left E03 42 xxxx xx1x DISPLAY: Combine Lower command to driver 1 = on
0 = off
3 = undefined
Left E03 42 xxxx xxx1 DISPLAY: Hillmaster Engage command to driver 1 = on
0 = off
3 = undefined
Left E03 43 xx1x xxxx DISPLAY: CAN Bus message from Armrest Control Unit - Grain Tank Cover Open Button 1 = button pressed
0 = button released
3 = message not received
Left E03 43 xxx1 xxxx DISPLAY: CAN Bus message from Armrest Control Unit - Grain Tank Cover Close Button 1 = button pressed
0 = button released
3 = message not received
Left E03 43 xxxx 1xxx DISPLAY: Grain Tank Cover Open relay output from Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 43 xxxx x1xx DISPLAY: Grain Tank Cover Close relay output from Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 43 xxxx xx1x DISPLAY: Grain Tank Cover Open command to Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 43 xxxx xxx1 DISPLAY: Grain Tank Cover Close command to Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 44 xxx1 xxxx DISPLAY: Spreader Speed Adjust driver status 1 = Output normal
0 = Output shorted or open

 

OUZXMAG,00018B2 -19-10OCT02-6/15

Control Unit Add. Line 2 Line 3 Description Details
Left E03 44 xxxx 1xxx DISPLAY: CAN Bus message from Armrest Control Unit - Spreader Speed Increase Button 1 = button pressed
0 = button released
3 = message not received
Left E03 44 xxxx x1xx DISPLAY: CAN Bus message from Armrest Control Unit - Spreader Speed Decrease Button 1 = button pressed
0 = button released
3 = message not received
Left E03 44 xxxx xx1x DISPLAY: Spreader Speed Increase command to driver 1 = on
0 = off
3 = undefined
Left E03 44 xxxx xxx1 DISPLAY: Spreader Speed Decrease command to driver 1 = on
0 = off
3 = undefined
Left E03 47 xxxx x1xx DISPLAY: Feeder House Reverser driver status 1 = Output normal
0 = Output shorted or open
Left E03 47 xxxx xx1x DISPLAY: Feeder House Reverser command to driver 1 = on
0 = off
3 = undefined
Left E03 47 xxxx xxx1 DISPLAY: CAN Bus message from Armrest Control Unit - Feeder House Reverser Switch 1 = on
0 = off
3 = message not received
Left E03 48 nnnn xxxx DISPLAY: Ground Speed Signal Shown in km/h X 10
Left E03 48 xxxx x1xx DISPLAY: Transmission Shift Lock Fuse Status (located on Control Relay Board) 1 = Normal
0 = Open
Left E03 48 xxxx xx1x DISPLAY: Transmission Shift Lock relay output from Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 48 xxxx xxx1 DISPLAY: Transmission Shift Lock command to Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 49 x1xx xxxx DISPLAY: Light Switch "Field" Signal 1 = on
0 = off
3 = undefined
Left E03 49 xx1x xxxx DISPLAY: Field Lights command to Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 49 xxx1 xxxx DISPLAY: Field Lights relay output from Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 49 xxxx x1xx DISPLAY: Light Switch "Road" Signal 1 = on
0 = off
3 = undefined
Left E03 49 xxxx xx1x DISPLAY: Road Lights command to Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 49 xxxx xxx1 DISPLAY: Road Lights relay output from Control Relay Board 1 = on
0 = off
3 = undefined

 

OUZXMAG,00018B2 -19-10OCT02-7/15

Control Unit Add. Line 2 Line 3 Description Details
Left E03 50 1xxx xxxx DISPLAY: Backup Light and Alarm Signal 1 = on
0 = off
3 = undefined
Left E03 50 x1xx xxxx DISPLAY: Light Switch "Road" Signal 1 = on
0 = off
3 = undefined
Left E03 50 xx1x xxxx DISPLAY: Light Switch "Rear" Signal 1 = on
0 = off
3 = undefined
Left E03 50 xxx1 xxxx DISPLAY: Light Switch "Stubble" Signal 1 = on
0 = off
3 = undefined
Left E03 50 xxxx 1xxx DISPLAY: Rear Lights output from Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 50 xxxx x1xx DISPLAY: Stubble Lights output from Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 50 xxxx xx1x DISPLAY: Rear Lights command to Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 50 xxxx xxx1 DISPLAY: Stubble Lights command to Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 51 1xxx xxxx DISPLAY: Light Switch "Hazard" Signal 1 = on
0 = off
3 = undefined
Left E03 51 x1xx xxxx DISPLAY: Light Switch "Road" Signal 1 = on
0 = off
3 = undefined
Left E03 51 xx1x xxxx DISPLAY: Turn Signal Switch "Left" 1 = on
0 = off
3 = undefined
Left E03 51 xxx1 xxxx DISPLAY: Turn Signal Switch "Right" 1 = on
0 = off
3 = undefined
Left E03 51 xxxx 1xxx DISPLAY: Left Turn Lamps relay output from Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 51 xxxx x1xx DISPLAY: Right Turn Lamps relay output from Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 51 xxxx xx1x DISPLAY: Left Turn Lamps command to Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 51 xxxx xxx1 DISPLAY: Right Turn Lamps command to Control Relay Board 1 = on
0 = off
3 = undefined

 

OUZXMAG,00018B2 -19-10OCT02-8/15

Control Unit Add. Line 2 Line 3 Description Details
Left E03 52 x1xx xxxx DISPLAY: Light Switch "Park" Signal 1 = on
0 = off
3 = undefined
Left E03 52 xx1x xxxx DISPLAY: Light Switch "Field" Signal 1 = on
0 = off
3 = undefined
Left E03 52 xxx1 xxxx DISPLAY: Light Switch "Road" Signal 1 = on
0 = off
3 = undefined
Left E03 52 xxxx 1xxx DISPLAY: Left Marker Lamps driver status 1 = Output normal
0 = Output shorted or open
Left E03 52 xxxx x1xx DISPLAY: Right Marker Lamps driver status 1 = Output normal
0 = Output shorted or open
Left E03 52 xxxx xx1x DISPLAY: Left Marker Lamps command to Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 52 xxxx xxx1 DISPLAY: Right Marker Lamps command to Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 53 xx1x xxxx DISPLAY: Turn Signal Switch "Left" 1 = on
0 = off
3 = undefined
Left E03 53 xxx1 xxxx DISPLAY: Turn Signal Switch "Right" 1 = on
0 = off
3 = undefined
Left E03 53 xxxx 1xxx DISPLAY: Left Brake Lamp driver status 1 = Output normal
0 = Output shorted or open
Left E03 53 xxxx x1xx DISPLAY: Right Brake Lamp driver status 1 = Output normal
0 = Output shorted or open
Left E03 53 xxxx xx1x DISPLAY: Left Brake Lamp command to driver 1 = on
0 = off
3 = undefined
Left E03 53 xxxx xxx1 DISPLAY: Right Brake Lamp command to driver 1 = on
0 = off
3 = undefined
Left E03 54 x1xx xxxx DISPLAY: Light Switch "Field" Signal 1 = on
0 = off
3 = undefined
Left E03 54 xx1x xxxx DISPLAY: Light Switch "Road" Signal 1 = on
0 = off
3 = undefined
Left E03 54 xxx1 xxxx DISPLAY: Unloading Auger Position 1 = Swung out past Latch Point - light enabled
0 = off
3 = undefined
Left E03 54 xxxx 1xxx DISPLAY: Driving Lamps relay output from Control Relay Board 1 = on
0 = off
3 = undefined

 

OUZXMAG,00018B2 -19-10OCT02-9/15

Control Unit Add. Line 2 Line 3 Description Details
Left E03 54 xxxx x1xx DISPLAY: Driving Lamps command to Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 54 xxxx xx1x DISPLAY: Auger Lamp driver status 1 = Output normal
0 = Output shorted or open
Left E03 54 xxxx xxx1 DISPLAY: Auger Lamp command to driver 1 = on
0 = off
3 = undefined
Left E03 55 1xxx xxxx DISPLAY: Light Power 5 (cc# 049) Monitor from Control Relay Board 1 = OK
0 = Not OK
3 = undefined
Left E03 55 x1xx xxxx DISPLAY: Fan Speed Adjust Power (cc# 051) Monitor from Control Relay Board 1 = OK
0 = Not OK
3 = undefined
Left E03 55 xx1x xxxx DISPLAY: Light Power 4 (cc# 048) Monitor from Control Relay Board 1 = OK
0 = Not OK
3 = undefined
Left E03 55 xxx1 xxxx DISPLAY: Light Power 3 (cc# 047) Monitor from Control Relay Board 1 = OK
0 = Not OK
3 = undefined
Left E03 55 xxxx 1xxx DISPLAY: Light Power 2 (cc# 046) Monitor from Control Relay Board 1 = OK
0 = Not OK
3 = undefined
Left E03 55 xxxx x1xx DISPLAY: Control Power (cc# 016) Monitor from Control Relay Board 1 = OK
0 = Not OK
3 = undefined
Left E03 55 xxxx xx1x DISPLAY: Light Power (cc# 014) Monitor from Control Relay Board 1 = OK
0 = Not OK
3 = undefined
Left E03 55 xxxx xxx1 DISPLAY: Unswitched Electronic Power (cc# 022) Monitor from Control Relay Board 1 = OK
0 = Not OK
3 = undefined
Left E03 56 xxx1 xxxx DISPLAY: Control Relay Board Watchdog Monitor 1 = OK
0 = Not OK
3 = undefined
Left E03 56 xxxx 1xxx DISPLAY: Delayed Power relay output from Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 56 xxxx x1xx DISPLAY: Delayed Power command to Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 56 xxxx xx1x DISPLAY: Control Relay Board Monitor 1 = OK
0 = Not OK
3 = undefined
Left E03 56 xxxx xxx1 DISPLAY: Internal Power Latch 1 = Latch On
0 = latch Off
3 = undefined

 

OUZXMAG,00018B2 -19-10OCT02-10/15

Control Unit Add. Line 2 Line 3 Description Details
Left E03 57 xxxx 1xxx DISPLAY: Ground (cc# 010) Monitor from Control Relay Board 1 = Ground OK
0 = Ground not OK
3 = undefined
Left E03 57 xxxx x1xx DISPLAY: Serial Data from Control Relay Board normal output will flicker between 1 and 0
Left E03 57 xxxx xx1x DISPLAY: Message from Control Relay Board - Key Switch Start 1 = START
0 = OFF, ACCESSORY or RUN
3 = undefined
Left E03 57 xxxx xxx1 DISPLAY: Message from Control Relay Board - Key Switch RUN 1 = RUN
0 = Off
3 = undefined
Left E03 58 x1xx xxxx DISPLAY: Grain Tank Cover Position Signal 1 = Open
0 = Closed
3 = undefined
Left E03 58 xx1x xxxx DISPLAY: Grain Tank 3/4 Full Signal 1 = Switch closed
0 = Switch open
3 = undefined
Left E03 58 xxx1 xxxx DISPLAY: Grain Tank Full Signal 1 = Switch closed
0 = Switch open
3 = undefined
Left E03 58 xxxx 1xxx DISPLAY: Beacon Lamps command to Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 58 xxxx x1xx DISPLAY: Beacon Lamp relay output from Control Relay Board 1 = on
0 = off
3 = undefined
Left E03 58 xxxx xx1x DISPLAY: CAN Bus message from Cornerpost Control Unit - Automatic Beacon Signal 1 = on
0 = off
3 = undefined
Left E03 58 xxxx xxx1 DISPLAY: Light Switch "Beacon" Signal 1 = on
0 = off
3 = undefined
Left E03 70 _ _ _ _ _ nnn DISPLAY: Unloading Auger Position Shown in percent of full extension
Left E03 71 _ _ _ _ nnnn DISPLAY: Left Control Unit Hours Time (shown in hours) the Left Control Unit has been powered.
Left E03 100 _ _ _ _ nnnn DISPLAY/MODIFY: Unloading Auger Swing Out Calibration Range = 8 - 26
Default = 12
Left E03 101 _ _ _ _ nnnn DISPLAY/MODIFY: Unloading Auger Swing In Calibration Range = 8 - 26
Default = 16
Left E03 102 _ _ _ _ _ nnn DISPLAY/MODIFY: Unloading Auger Light On Position Range = 5% - 95%
Default = 50%
Left E03 103 _ _ _ _ _ nnn DISPLAY/MODIFY: Unloading Auger Engage Latch Position Range = 5% - 95%
Default = 50%
Left E03 104 _ _ _ _ _ nnn DISPLAY/MODIFY: Delayed Power time-out Range = 180 - 600 seconds
Default = 180 seconds
Left E03 105 _ _ _ _ _ nnn DISPLAY/MODIFY: Exit Light time-out Range = 30 - Delayed Power Time-out
Default = 90 seconds

 

OUZXMAG,00018B2 -19-10OCT02-11/15

Control Unit Add. Line 2 Line 3 Description Details
Left E03 106 _ _ _ _ _ nnn DISPLAY/MODIFY: Straw Spreader Speed duty cycle Milliseconds ON during a 300 millisecond cycle
Range = 0 - 300 milliseconds
Default = 30 milliseconds
Left E03 107 _ _ _ _ _ nnn DISPLAY/MODIFY: Draper Speed duty cycle Milliseconds ON during a 300 millisecond cycle
Range = 0 - 300 milliseconds
Default = 30 milliseconds
Left E03 108 _ _ _ _ nnnn DISPLAY/MODIFY: Minimum Cleaning Fan Speed Range = 600 - 1000 rpm
Default = 700 rpm
Left E03 109 _ _ _ _ nnnn DISPLAY/MODIFY: Maximum Cleaning Fan Speed Range = 1000 - 1650 rpm
Default = 1400 rpm
Left E03 120 x1xx xxxx DISPLAY/MODIFY: Beacon Lamps (cc# 556) 1 = ON
2 = Flashing
0 = OFF
Left E03 120 xx1x xxxx DISPLAY/MODIFY: Command to Control Relay Board - Driving Lamps (cc# 545) 1 = ON
2 = Flashing
0 = OFF
Left E03 120 xxx1 xxxx DISPLAY/MODIFY: Unloading Auger Lamp (cc# 562) 1 = ON
2 = Flashing
0 = OFF
Left E03 120 xxxx 1xxx DISPLAY/MODIFY: Command to Control Relay Board - Rear Lamps (cc# 559) 1 = ON
2 = Flashing
0 = OFF
Left E03 120 xxxx x1xx DISPLAY/MODIFY: Command to Control Relay Board - Stubble Lamps (cc# 529) 1 = ON
2 = Flashing
0 = OFF
Left E03 120 xxxx xx1x DISPLAY/MODIFY: Command to Control Relay Board - Field Lamps (cc# 507) 1 = ON
2 = Flashing
0 = OFF
Left E03 120 xxxx xxx1 DISPLAY/MODIFY: Command to Control Relay Board - Road Lamps (cc# 526) 1 = ON
2 = Flashing
0 = OFF
Left E03 121 xx1x xxxx DISPLAY/MODIFY: Left Rear Red Hazard Lamps (cc# 565) 1 = ON
2 = Flashing
0 = OFF
Left E03 121 xxx1 xxxx DISPLAY/MODIFY: Right Rear Red Hazard Lamps (cc# 564) 1 = ON
2 = Flashing
0 = OFF
Left E03 121 xxxx 1xxx DISPLAY/MODIFY: Command to Control Relay Board - Left Turn Lamps (cc# 515) 1 = ON
2 = Flashing
0 = OFF
Left E03 121 xxxx x1xx DISPLAY/MODIFY: Command to Control Relay Board - Right Turn Lamps (cc# 514) 1 = ON
2 = Flashing
0 = OFF
Left E03 121 xxxx xx1x DISPLAY/MODIFY: Left Marker Lamps (cc# 552) 1 = ON
2 = Flashing
0 = OFF

 

OUZXMAG,00018B2 -19-10OCT02-12/15

Control Unit Add. Line 2 Line 3 Description Details
Left E03 121 xxxx xxx1 DISPLAY/MODIFY: Right Marker Lamps (cc# 553) 1 = ON
2 = Flashing
0 = OFF
Left E03 122 xxxx 1xxx DISPLAY/MODIFY: Command to Control Relay Board - Cleaning Fan Speed Increase (cc# 306) 1 = ON
2 = Flashing
0 = OFF
Left E03 122 xxxx x1xx DISPLAY/MODIFY: Command to Control Relay Board - Cleaning Fan Speed Decrease (cc# 307) 1 = ON
2 = Flashing
0 = OFF
Left E03 122 xxxx xx1x DISPLAY/MODIFY: Command to Control Relay Board - Threshing Clearance Increase (cc# 312) 1 = ON
2 = Flashing
0 = OFF
Left E03 122 xxxx xxx1 DISPLAY/MODIFY: Command to Control Relay Board - Threshing Clearance Decrease (cc# 313) 1 = ON
2 = Flashing
0 = OFF
Left E03 123 1xxx xxxx DISPLAY/MODIFY: Command to Control Relay Board - Chopper Vane Left (cc# 364) 1 = ON
2 = Flashing
0 = OFF
Left E03 123 x1xx xxxx DISPLAY/MODIFY: Command to Control Relay Board - Chopper Vane Right (cc# 365) 1 = ON
2 = Flashing
0 = OFF
Left E03 123 xx1x xxxx DISPLAY/MODIFY: Command to Control Relay Board - Grain Tank Cover Open (cc# 332) 1 = ON
2 = Flashing
0 = OFF
Left E03 123 xxx1 xxxx DISPLAY/MODIFY: Command to Control Relay Board - Grain Tank Cover Close (cc# 333) 1 = ON
2 = Flashing
0 = OFF
Left E03 123 xxxx 1xxx DISPLAY/MODIFY: Threshing Speed Change (cc# 305) 1 = ON
2 = Flashing
0 = OFF
Left E03 123 xxxx x1xx DISPLAY/MODIFY: Unloading Auger Engage (cc# 319) 1 = ON
2 = Flashing
0 = OFF
Left E03 123 xxxx xx1x DISPLAY/MODIFY: Unloading Auger Swing Out (cc# 317) 1 = ON
2 = Flashing
0 = OFF
Left E03 123 xxxx xxx1 DISPLAY/MODIFY: Unloading Auger Swing In (cc# 316) 1 = ON
2 = Flashing
0 = OFF
Left E03 125 x1xx xxxx DISPLAY/MODIFY: Left Four Wheel Drive High Speed (cc# 207) 1 = ON
2 = Flashing
0 = OFF
Left E03 125 xx1x xxxx DISPLAY/MODIFY: Right Four Wheel Drive High Speed (cc# 208) 1 = ON
2 = Flashing
0 = OFF
Left E03 125 xxx1 xxxx DISPLAY/MODIFY: Four Wheel Drive Engage (cc# 202) 1 = ON
2 = Flashing
0 = OFF

 

OUZXMAG,00018B2 -19-10OCT02-13/15

Control Unit Add. Line 2 Line 3 Description Details
Left E03 125 xxxx 1xxx DISPLAY/MODIFY: Hillmaster Left Signal (cc# 476) 1 = ON
2 = Flashing
0 = OFF
Left E03 125 xxxx xxx DISPLAY/MODIFY: Hillmaster Right Signal (cc# 477) 1 = ON
2 = Flashing
0 = OFF
Left E03 125 xxxx xx1x DISPLAY/MODIFY: Combine Lower (cc# 905) 1 = ON
2 = Flashing
0 = OFF
Left E03 125 xxxx xxx1 DISPLAY/MODIFY: Hillmaster Engage Signal (cc# 447) 1 = ON
2 = Flashing
0 = OFF
Left E03 126 xxx1 xxxx DISPLAY/MODIFY: Feeder House Reverser (cc# 442) 1 = ON
2 = Flashing
0 = OFF
Left E03 126 xxxx x1xx DISPLAY/MODIFY: Command to Control Relay Board - Transmission Lockout (cc# 209) 1 = ON
2 = Flashing
0 = OFF
Left E03 126 xxxx xx1x DISPLAY/MODIFY: Climatrak Clutch (cc# 913) 1 = ON
2 = Flashing
0 = OFF
Left E03 126 xxxx xxx1 DISPLAY/MODIFY: Command to Control Relay Board - Ignition Switch "Start" (cc# 107). Output of this relay will depend on condition of Ignition Switch "Start" Signal (cc# 104) 1 = ON
2 = Flashing
0 = OFF
Left E03 127 xxxx x1xx DISPLAY/MODIFY: Serial Data TXD (cc# 985) 1 = ON
2 = Flashing
0 = OFF
Left E03 127 xxxx xx1x DISPLAY/MODIFY: Serial Data Clock (cc# 987) 1 = ON
2 = Flashing
0 = OFF
Left E03 127 xxxx xxx1 DISPLAY/MODIFY: Serial Data Load (cc# 988) 1 = ON
2 = Flashing
0 = OFF
Left E03 200 _ _ nn nnnn DISPLAY: Flash memory part number  
Left E03 227 _ _ nn nnnn DISPLAY: Part number of the boot block program  
Left E03 228 _ _ _ _ nnnn DISPLAY: Version number of the boot block program  
Left E03 233 _ _ nn nnnn DISPLAY: Base program part number  
Left E03 234 _ _ _ _ nnnn DISPLAY: Base program version number  
Left E03 235 _ _ nn nnnn DISPLAY: Device part number  

 

OUZXMAG,00018B2 -19-10OCT02-14/15

Control Unit Add. Line 2 Line 3 Description Details
Left E03 236 nnnn nnnn DISPLAY: Device serial number  
Left E03 247 _ _ _ _ _ _ nn DISPLAY: Machine Model Number 14 - 9640, 9660, 9680
16 - 9540, 9560, 9580

 

OUZXMAG,00018B2 -19-10OCT02-15/15