OCP Addresses - Overhead Control Panel Control Unit
|
|
| OCP - Overhead Control Panel Control Unit |
| Addresses |
|
| Number |
Type |
Description |
| 002 |
Standard |
Beep Mode |
| 003 |
Standard |
Limited System Beep Mode |
| 004 |
Standard |
Analog Beep Mode |
| 005 |
Standard |
Digital Beep Mode |
| 010 |
Analog Input |
Backlight Power
Display in Volts |
| 011 |
Analog Input |
Battery Voltage
Display in Volts |
| 050 |
Digital Input |
Digital Input 01
Following data are transmitted: Home Position Switch, Stationary Knife Adjust Switch, Stationary Knife Away Switch, Kernel Processor Adjust Abort Switch, Kernel Processor Adjust Switch, Powr-Savr Interlock Relay Closed Input, Powr-Savr Request Enable Input, Powr-Savr Interlock Relay Driver Status Input
See also "Address OCP 050 - Digital Input 01"
Entering OBD-Addresses see "On-Board Diagnostic - Entering Addresses" |
| 051 |
Digital Input |
Digital Input 02
Following data are transmitted: Indication Lamp Driver Fault Input, Cutterhead Sharpen Switch
See also "Address OCP 051 - Digital Input 02"
Entering OBD-Addresses see "On-Board Diagnostic - Entering Addresses" |
| 052 |
Digital Input |
Digital Input 03
Following data are transmitted: Row Guidance Enable Switch, Metal Detector Calibration Switch, Metal Detector Enable Switch
See also "Address OCP 052 - Digital Input 03"
Entering OBD-Addresses see "On-Board Diagnostic - Entering Addresses" |
| 053 |
Digital Input |
Digital Input 04
Following data are transmitted: Reset Switch, Metal Detector Test Switch, Metal Detector Initial Threshold Calibration Switch
See also "Address OCP 053 - Digital Input 04"
Entering OBD-Addresses see "On-Board Diagnostic - Entering Addresses" |
| 140 |
Digital Output |
Digital Output 01
Following data are transmitted: Metal Detector Center Left Lamp, Metal Detector Center Right Lamp, Metal Detector Right Lamp, Metal Detector Calibration / Test Lamp, Row Guidance Enable Lamp, Cutterhead Sharpen Active Lamp, Stationary Knife Adjust Active Lamp, Kernel Processor Adjust Active Lamp
See also "Address OCP 140 - Digital Output 01"
Entering OBD-Addresses see "On-Board Diagnostic - Entering Addresses" |
| 141 |
Digital Output |
Digital Output 02
Following data are transmitted: Metal Detector Enable Lamp, Metal Detector Left Lamp
See also "Address OCP 141 - Digital Output 02"
Entering OBD-Addresses see "On-Board Diagnostic - Entering Addresses" |
| 142 |
Digital Output |
Digital Output 03
Following data are transmitted: Red Stop Lamp, Amber Warning Lamp, Protect Lamp, Indication Lamp Driver Enable, Backlight Output, Row Guidance Power Relay Driver Output
See also "Address OCP 142 - Digital Output 03"
Entering OBD-Addresses see "On-Board Diagnostic - Entering Addresses" |
|
|
OUZXMAY,0000437 -19-01NOV02-1/2
|
| OCP - Overhead Control Panel Control Unit |
| Addresses |
|
| Number |
Type |
Description |
| 143 |
|
Alarm Monitor
Following data are transmitted: Control Panel Alarm Request, Row Guidance Alarm Request, Armrest Alarm Request, Corner Post Alarm Request, Metal Detector Alarm Request, SPFH Main Control Unit Alarm Request
See also "Address OCP 143 - Digital Output 04"
Entering OBD-Addresses see "On-Board Diagnostic - Entering Addresses" |
| 198 |
Display - Operator |
Cutterhead Operating Time |
| 199 |
Display - Operator |
Machine Operating Time |
|
|
OUZXMAY,0000437 -19-01NOV02-2/2
|
|