OMM134807

Issue A9

F725

Front Mowers PIN (090001- )

Introduction

Safety Signs

Controls

Operating Machine

Operating Mower

Lawn Care

Replacement Parts

Service Machine Safely

Service Interval Chart

Service Engine

Service Transmission

Transmission And Hydraulic Oil

Checking The Transmission Oil Level

Changing The In-line Hydraulic Oil Filter

Changing The Hydraulic Sump (Transaxle) Filter

Changing The Transmission Oil

Replacing The Transmission Belt

Adjusting Transmission Neutral

Service Steering & Brakes

Service Mower

Service Electrical

Service Miscellaneous

Removing Mower

Installing Mower

Troubleshooting

Storing Machine

Assembly

Specifications

Warranty

John Deere Service Literature

QUALITY DOESN'T END WHEN YOU INVEST IN A DEERE

Service Transmission

Transmission And Hydraulic Oil

MIF

NOTE: Tractor is filled with John Deere HY-GARD® (J20C) transmission oil at the factory. DO NOT mix oils.

Use only HY-GARD® (J20C) transmission oil.

Do not use type "F" automatic transmission fluid.

John Deere HY-GARD® (J20C) transmission oil is specially formulated to provide maximum protection against mechanical wear, corrosion, and foaming.

Checking The Transmission Oil Level

Check the oil level before you start the engine.

M7339

1. Lift the seat to the second position.

2. Turn the dipstick (A) to remove it.

3. Wipe the dipstick. Install it but do not turn it. Pull it out.

4. Oil should be in the XX area at the bottom of the dipstick.

5. If not, pour oil into the dipstick tube.

6. Install and tighten the dipstick.

7. Lower the seat.

Changing The In-line Hydraulic Oil Filter

1. STOP the engine. LOCK the park brake. Wait until the engine and the transmission are cool.

2. Lift and open the hood.

c CAUTION: Avoid injury! Escaping fluid under pressure can penetrate the skin causing serious injury. Avoid the hazard by relieving pressure before disconnecting hydraulic or other lines. Tighten all connections before applying pressure. Search for leaks with a piece of cardboard. Protect hands and body from high pressure fluids.

3. Remove the hydraulic filter (A):

M73366

· Loosen the two fittings (B).

· Catch dripping oil in a container.

· Install a new filter with an O-ring on each side.

4. Tighten the two fittings.

5. Also change the hydraulic sump filter (next).

6. Lower the hood.

Changing The Hydraulic Sump (Transaxle) Filter

c CAUTION: Avoid injury! Escaping fluid under pressure can penetrate the skin causing serious injury. Avoid the hazard by relieving pressure before disconnecting hydraulic or other lines. Tighten all connections before applying pressure. Search for leaks with a piece of cardboard. Protect hands and body from high pressure fluids.

M73435

1. Use a filter wrench to turn the sump filter (A) counterclockwise. Remove the filter.

2. Catch dripping oil in a container.

3. Put a film of clean transmission oil on the seal of the new filter.

4. Install the filter. Turn it clockwise until it contacts the mounting surface.

5. Then turn the filter 1/2 turn more.

6. Run the engine a short time. Stop the engine.

7. Check the hydraulic oil level. See Checking The Transmission Oil Level in this section.

8. Add oil, if necessary. Do not run the engine if the transmission oil level is low.

Changing The Transmission Oil

c CAUTION: Avoid injury! Escaping fluid under pressure can penetrate the skin causing serious injury. Avoid the hazard by relieving pressure before disconnecting hydraulic or other lines. Tighten all connections before applying pressure. Search for leaks with a piece of cardboard. Protect hands and body from high pressure fluids.

1. STOP the engine. LOCK the park brake. Wait until the engine and the transmission are cool.

2. Remove the transmission oil dipstick.

3. Put a container under the drain plug (A).

M73392

4. Remove the plug. Drain the oil. Install the plug.

5. Pour oil into the dipstick tube. The capacity is 2.4 L (2.5 qt).

6. Install and tighten the dipstick.

7. Run the engine a short time. Stop the engine.

8. Check the transmission oil level. See Checking The Transmission Oil Level in this section.

Replacing The Transmission Belt

1. STOP the engine.

2. Lift the seat to the second position.

3. Stand on the left side of the Front Mower. Pull and hold the idler sheave toward you (A).

M73460

4. Remove the belt from the front sheave (B) and the rear sheave.

5. Pull and hold the idler sheave as you install the new belt.

6. Lower the seat.

Adjusting Transmission Neutral

Adjust transmission neutral to assure that machine DOES NOT creep when pedals are in the neutral position.

You will need a jumper wire, floor jack, and jackstand for this procedure.

1. Park machine on level surface. Park brake disengaged. PTO disengaged. Transmission in neutral.

2. Block right drive wheel to prevent machine from moving.

3. Raise left drive wheel off ground with floor jack. Place a jackstand under left axle housing to prevent wheel from dropping.

NOTE: DO NOT engage differential lock during this adjustment.

4. Have someone push down center of seat cushion to activate seat safety switch, or disconnect connector from seat switch and install jumper wire across wiring harness connector posts.

c CAUTION: Avoid injury! Be sure to remove jumper, if installed, from seat switch when adjustment is completed. Reconnect connector to seat switch.

NOTE: DO NOT turn PTO switch to the on position as the operator presence circuit is bypassed for this procedure and the PTO could engage.

5. Loosen bolt (A) on adjuster cam (B).

M49859

c CAUTION: Avoid injury! To avoid injury, watch for rotating transmission sheave.

6. Start engine and run at fast idle.

M49859

7. Rotate cam (C) until left wheel does NOT spin.

8. Tighten bolt. Readjust cam if wheel begins to spin again.