OMMT596
Issue H5
3365 Professional Turf Mower
Serial No. (010001 - )
Cutting Units
Ground Speed
Frequency
Engine
Fuel System
Hydraulic System
Electrical System
Capacities
Drive Train
Travel Speeds
Dimensions
Tires
Recommended Lubricants
Tightening O-Ring Fittings
Tightening O-Rings Fittings (Continued)
CopyrightŠ Deere & Company
|
Specifications
Cutting Units
Number of Cutting Units
|
5
|
Cutting Width
|
3.5 m (11 ft 6 in.)
|
Cutting Unit Lift
|
Single acting cylinder
|
Cutting Unit Suspension
|
Outrigger arms, trailing arm for center mower
|
Cutting Unit Mounting
|
Floating, lateral, fore and aft, with fixed position lockout
|
Cutting Unit Width
|
762 mm (30 in.)
|
Reel Diameter
|
197 mm (7-3/4 in.)
|
Number of Blades
|
6 standard; 8, or 10 optional
|
Cutter Drive
|
Hydraulic gear motor, 2.5:1 reduction gear case
|
Hydraulic Motor
|
Gear type
|
Reel Speed
|
1250 rpm
|
Filtration
|
Full flow replaceable cartridge, 10 micron in return line
|
Cutting Height
|
9.5 to 76 mm (3/8 to3 in.)
|
Ground Speed
7 km/h
|
4.5 mph
|
8 km/h
|
5.0 mph
|
9 km/h
|
5.5 mph
|
10 km/h
|
6.0 mph
|
11 km/h
|
6.5mph
|
11.6 km/h
|
7.2mph
|
Frequency
6 Blade
mm (in.)
|
8 Blade
mm (in.)
|
10 Blade
mm (in.)
|
16.0 (0.63.)
|
12.0 (0.47)
|
10.0 (0.38)
|
18.0 (0.71)
|
13.0 (0.51)
|
11.0 (0.42)
|
20.0 (0.78)
|
15.0 (0.59)
|
12.0 (0.47)
|
22.0 (0.85)
|
16.0 (0.63)
|
13.0 (0.51)
|
23.0 (0.92)
|
18.0 (0.71)
|
14.0 (0.55)
|
26.0 (1.02)
|
19.0 (0.75)
|
15.0 (0.59)
|
Engine
Model
|
Yanmar
|
Engine Model Number
|
4TN82-RJE
|
Horsepower
|
38 @ 2700 (28.9 kW)
|
Cylinders
|
4
|
|
86 mm (3.23 in.)
|
Displacement
|
1.8L, 1816 cu (110.8 cu in.)
|
Bore
|
82 mm (3.23 in)
|
Speed (fast idle), no load
|
2800
|
Speed (slow idle), no load
|
1000
|
Fuel System
Hydraulic System
Pump Type
Gear
|
Output
39L/min @2700 engine rpm (10.3 gpm) per pump
|
Electrical System
Type
|
12 Volt negative (-) ground
|
Charging System
|
Alternator, 40 Amp with internal regulator
|
Battery
|
group 24F 550 CCA minimum
|
Air Heater
|
400 Watts
|
Capacities
Fuel Tank
|
75.5 L (20 gal)
|
Mower Hydraulic Reservoir
|
26.5 L (7 gal)
|
Hydraulic Pump Capacity
|
Parallel pump system -39 L min (10.3 gpm) per pump
|
Engine Oil (with filter)
|
5.8 L (6 qt)
|
Traction Unit Hydrostatic Transaxle/Hydraulic System
|
18.9 L (5 gal)
|
Cutting Unit Gear Case
|
0.4 L (0.8 pt)
|
Drive Train
Travel Speeds
Low Range
|
0 to 11.6 km/h (0 to 7.2 mph)
|
High Range
|
0 to 18.8 km/h (0 to 11.7 mph)
|
Dimensions
Height (Cutting Units Folded)
|
1.35 m (53 in.)
|
Height (Cutting Units Unfolded)
|
1 m (39.5 in.)
|
Height (with ROPS)
|
1.93 m (76 in.)
|
Overall Width:
|
3.74 m (150 in.)
|
Transport Width
|
2.26 m (89 in.)
|
Overall Length
|
2.74 m ((108 in.)
|
Wheelbase
|
1.30 m (51.25 in.)
|
Operating Weight
|
1619 kg (3570 lb)
|
Shipping Weight
|
1120 kg (2470 lb)
|
Tires
Front
|
33 x 12.50 - 15 4-PR
|
Rear
|
23 x 10.50 - 12 4-PR
|
Pressure
|
62 kPa (9 psi) (0.6 bar)
|
Recommended Lubricants
Fuel
|
Diesel
|
Engine Oil
|
John Deere TORQ-GARD SUPREME PLUS-50TM
|
Engine Coolant
|
Ethylene Glycol Base
|
Transmission Oil
|
John Deere Hy-Gard or Equivalent to JDM J20C
|
Grease
|
John Deere MOLY HIGH TEMPERATURE EP GREASE
John Deere HIGH TEMPERATURE EP GREASE
John Deere GREASE GARDTM
|
(Specifications and design subject to change without notice.)
Tightening O-Ring Fittings
1. Inspect O-ring and seat for dirt or obvious defects.
2. On angle fittings, back the lock nut off until washer bottoms out at top of groove.
3. Hand tighten fitting until backup washer or washer face (if straight fitting) bottoms on face and O-ring is seated.
4. Position angle fittings by unscrewing no more than one turn.
5. Tighten straight fittings to torque shown.
6. Tighten angle fittings to torque shown while holding the body of fitting with a wrench.
Tightening O-Rings Fittings (Continued)
Thread Size (in.)
|
Nut Size Across Flats (in.)
|
Torque Value
(Nˇm)-- (lb-ft)
|
Recommended Turns To Tighten (After Finger Tightening)
(Flats) -- (Turns)
|
3/8
|
1/2
|
8
|
6
|
2
|
1/3
|
7/16
|
9/16
|
12
|
9
|
2
|
1/3
|
1/2
|
5/8
|
16
|
12
|
2
|
1/3
|
9/16
|
11/16
|
24
|
18
|
2
|
1/3
|
3/4
|
7/8
|
46
|
34
|
2
|
1/3
|
7/8
|
1
|
62
|
46
|
1-1/2
|
1/4
|
1-1/16
|
1-1/4
|
102
|
75
|
1
|
1/6
|
1-3/16
|
1-3/8
|
122
|
90
|
1
|
1/6
|
1-5/16
|
1-1/2
|
142
|
105
|
3/4
|
1/8
|
1-5/8
|
1-7/8
|
190
|
140
|
3/4
|
1/8
|
1-7/8
|
2-1/8
|
217
|
160
|
1/2
|
1/12
|
|