5303 Tractor
Copyright 2002 (c) Deere & Company. THIS DATA IS THE PROPERTY OF DEERE & COMPANY. ALL USE AND/OR REPRODUCTION NOT SPECIFICALLY AUTHORIZED BY DEERE & COMPANY IS PROHIBITED.
All information, illustrations and specifications in this manual are based on the latest information available at the time of publication. The right is reserved to make changes at any time without notice.
Foreword
Section : 05 - Safety
Recognize Safety Information
Understand Signal Words
Follow Safety Instructions
Prevent Machine Runaway
Use Seat Belt and ROPS Properly
Operate Tractor Safely
Use Caution on Hillsides
Shift to Low Gear on Hills
Avoid Tipping
Freeing a Mired Machine
Work In Ventilated Area
Park Tractor Safely
Keep Riders Off Machine
Handle Fuel Safely-Avoid Fires
Prepare for Emergencies
Do Not Use Starting Fluid
Wear Protective Clothing
Protect Against Noise
Handle Agricultural Chemicals Safely
Service and Operate Chemical Sprayers Safely
Stay Clear of Rotating Drivelines
Use Safety Lights and Devices
Use a Safety Chain
Safely Transporting the Tractor
Tow Loads Safely
Keep ROPS Installed Properly
Practice Safe Maintenance
Service Tractor Safely
Support Machine Properly
Remove Paint Before Welding or Heating
Avoid Heating Near Pressurized Fluid Lines
Avoid High-Pressure Fluids
Service Cooling System Safely
Store Attachments Safely
Prevent Acid Burns
Service Tires Safely
Dispose of Waste Properly
Section : 10 - Safety Signs
Warning Labels
Section : 15 - Controls and Instruments
Tractor Controls
Instrument Panel
Section : 20 - Lights
Light Switch Positions
Using Headlights
Using High Beam Indicator
Using Tail Lights
Using Turn Signals
Using Hazard Lights
Using Rear Flood Light
Adjusting Rear Flood Light
Section : 25 - Operator's Platform
Operating Foldable ROPS (If Equipped)
Adjusting Ride Comfort
Selecting Seat Position
Section : 30 - Break-In Period
Observe Engine Operation Closely
Break-In Service
Section : 35 - Prestarting Checks
Service Daily Before Start-Up
Section : 40 - Operating the Engine
Before Starting the Engine
Starting the Engine
Check Instruments After Starting
Oil Pressure Indicator
Charging System Indicator
Air Restriction Indicator
Coolant Temperature Gauge
Watch Fuel Level
Changing Engine Speeds
Warming Up the Engine
Restart Stalled Engine
Avoid Idling the Engine
Observe Engine Work and Idle Speeds
Working With Speed/Hour Meter
Using Booster Battery
Section : 45 - Driving the Tractor
Operator Training Required
Avoid Contact with Pesticides
Driving on Public Roads
Operating Transmission
Shifting Transmission
Selecting a Gear
Using Brakes
Using Differential Lock
Stopping Tractor
Section : 55 - Rockshaft and 3-Point Hitch
Match Tractor Power to Implement
3-Point Hitch Components
Rockshaft Control Levers
Setting Position Control Lever Stop
Using Rockshaft Position Control
Using Draft Control
Adjusting Rockshaft Rate-of-Drop/ Implement lock
Attaching Tipping Trailer
Preparing Implement
Positioning Center Link
Attaching Implements to 3-Point Hitch
Adjusting Hitch Side Sway
Leveling the Hitch
Adjusting Lateral Float
Adjusting Rockshaft Control Lever Friction - MITA Rockshaft
Adjusting Rockshaft Lever Friction Adjustment - New JD Rockshaft
Warming Hydraulic System Oil
Section : 60 - Remote Hydraulic Cylinders
Use Correct Hose Tips
Control Lever and Coupler Identification-If Equipped
Connecting Hoses
Connecting Single-Acting Cylinder
Correcting Reversed Cylinder Response
Neutral Lever Position
Extending/Retracting Cylinder
Disconnecting Hoses
Observe Drawbar / Wagon Hitch Load Limitations
Stay Clear of Rotating Drivelines
Selecting Drawbar Position
Adjusting Drawbar Length
Using Swinging Drawbar
Attaching PTO-Driven Implement
Operating Tractor PTO
Adjusting PTO Clutch Operating Rod
Section : 65 - Ballast
Planning for Maximum Productivity
Selecting Ballast Carefully
Matching Ballast to Load Work
Checking for Correct Ballast
Measuring Wheel Slip-Manually
Ballast Limitations
Ballasting Front End for Transport
Ballasting Two-Wheel Drive Tractors
Determining Maximum Rear Ballast
Determining Maximum Front Ballast
Using Cast Iron Weights
Installing Rear Cast Iron Weights
Using Liquid Weight
Using Implement Codes
Section : 70 - Wheels, Tires and Treads
Service Tires Safely
Check Implement-to-Tire Clearance
Check Tire Inflation Pressure
Tire Inflation Pressure Chart
Selecting Front Tire Rolling Direction
Tighten Wheel/Axle Hardware Correctly
Tighten Bolts-Adjustable Front Axle
Tighten Bolts-Rear Axle
Observe Rear Wheel Tread Width Limitations
Tread Settings-Multi-Position Rear Wheels
Tread Settings-Adjustable Front Axle
Adjust Front Axle Tread Width
Checking Toe-In
Adjusting Toe-In-Two-Wheel Drive Tractor
Use Correct Tire Combinations
Section : 75 - Transporting
Use Safety Lights and Devices
Use a Safety Chain
Driving Tractor on Roads
Transport on Carrier
Towing Tractor
Section : 80 - Fuels, Lubricants and Coolant
Handle Fuel Safely-Avoid Fires
Handle Fluids Safely-Avoid Fires
Fuel Storage
Cold Weather Operation
Diesel Fuel
Handling and Storing Diesel Fuel
Bio-Diesel Fuel
Fill Fuel Tank
Alternative and Synthetic Lubricants
Lubricant Storage
Diesel Engine Oil
Oil Filters
Diesel Engine Coolant
Liquid Coolant Conditioner
Anti-Chatter Transmission/Hydraulic Oil
Use Correct Hydraulic-Transmission Filter Element
Gear Oil
Grease
Section : 85 - Lubrication and Maintenance
Avoid Heating Near Pressurized Fluid Lines
Clean Vehicle of Hazardous Pesticides
Observe Service Intervals
Use Correct Lubricant
Break-In Service
Service Intervals
Section : 90 - Service-Every 10 Hours
Check Engine Oil Level
Check Coolant Level
Drain Water and Sediment from Fuel Tank
Lubricate as Necessary
Section : 95 - Service-50 Hours
Check Transmission-Hydraulic System Oil Level
Clean and Check Battery
Inspect All Tires
Lubricate Front Axle Pivot Pin
Lubricate Steering Spindles
Inspect Tractor for Loose Hardware
Section : 100 - Service-100 Hours
Change Engine Oil and Filter
Replace Transmission-Hydraulic Filter
Section : 105 - Service-250 Hours
Service Air Cleaner
Inspect and Adjust Alternator/Fan Belt
Lubricate 3-Point Hitch
Check Neutral Start System
Check and Adjust Clutch Pedal Free Play
Section : 110 - Service-500 Hours
Replace Fuel Filter
Section : 115 - Service-Every 600 Hours
Clean Engine Crankcase Vent Tube
Pack Front Wheel Bearings
Check Hoses and Hose Clamps for Tightness
Lubricate Rear Axle Bearings
Check Engine Idle Speeds
Check Front Axle Pivot Pin
Adjust Engine Valve Clearance
Section : 120 - Service-Every 1200 Hours
Change Transmission-Hydraulic Oil and Filter
Clean Transmission-Hydraulic Pickup Screen
Section : 125 - Service-Annually
Replace Air Cleaner Elements
Section : 130 - Service-2 Years/2000 Hours
Flush Cooling System
Section : 135 - Service-As Required
Service Air Cleaner
Adjust Throttle Friction
Section : 140 - Service
Additional Service Information
Engine Break-In Oil
Work In Ventilated Area
Using High-Pressure Washers
Opening Hood
Removing Side Screens
Removing Hood
Air Intake System Components
Service Air Cleaner at Regular Intervals
Checking Air Intake System
Removing Primary Air Cleaner Element
Cleaning Primary Element
Washing Primary Element
Inspecting Element
Storing Element
Replacing Alternator/Fan Belt
Fuel System Components
Do Not Modify Fuel System
Bleeding Fuel System
Bleed Fuel System At Fuel Injection Nozzles
Engine Cooling System
Cleaning Grille, Screens, Radiator and Oil Cooler
Prevent Battery Explosions
Observe Electrical Service Precautions
Battery Access
Removing Battery
Checking Battery Condition
Servicing Battery
Charging Battery
Battery Replacement Specifications
Connecting Starter Wiring
Connecting Alternator Wiring
Locating Fusible Link
Locating Fuses
Fuse Size and Function
Aiming Headlights
Adjusting Headlights
Replace Headlight Bulb
Replace Tail Light Bulb
Replace Flood Light Bulb
Checking Tires
Section : 150 - Troubleshooting
Engine Troubleshooting
Transmission Troubleshooting
Hydraulic System Troubleshooting
Brakes Troubleshooting
Rockshaft and Quick-Coupler 3-Point Hitch Troubleshooting
Remote Hydraulic Cylinders Troubleshooting
Electrical System Troubleshooting
Section : 155 - Tractor Storage
Storing Tractor
Removing Tractor From Storage
Section : 160 - Specifications
John Deere 5303 Tractor
Ground Speed at Rated Engine Speed (2400 rpm)
Metric Bolt and Screw Torque Values
Unified Inch Bolt and Screw Torque Values
Section : 165 - Identification Numbers
Identification Plates
Record Tractor Serial Number
Record Front Axle Serial Number
Record Engine Serial Number
Record Transmission Serial Number
Keep Proof of Ownership
Keep Machines Secure
Section : 170 - Lubrication Maintenance Record Charts
50, 250, 500 Hour Service Chart
600 Hour Service Chart
1000, 1200 Hour Service Chart
Annual Service Chart
2000 Hour Service Chart
As Required Service Chart
Section : 180 - John Deere Service
John Deere Parts
The Right Tools
Well Trained Technician
Prompt Service