4044M, 4044R, 4052M, 4052R, 4066M, and 4066R
Tractors Operator's Manual (North America)
Copyright 2018 © Deere & Company. THIS DATA IS THE PROPERTY OF DEERE & COMPANY. ALL USE AND/OR REPRODUCTION NOT SPECIFICALLY AUTHORIZED BY DEERE & COMPANY IS PROHIBITED.
All information, illustrations and specifications in this manual are based on the latest information available at the time of publication. The right is reserved to make changes at any time without notice.
Foreword
00 - General Information
Product View
Trademarks
Glossary of Terms
Regions and Country Versions
Machine Overview
00A - Safety
Recognize Safety Information
Understand Signal Words
Follow Safety Instructions
Prepare for Emergencies
Wear Protective Clothing
Protect Against Noise
Handle Fuel Safely—Avoid Fires
Handle Starting Fluid Safely
Fire Prevention
In Case of Fire
Avoid Static Electricity Risk When Refueling
Keep ROPS Installed Properly
Use Foldable ROPS and Seat Belt Properly
Stay Clear of Rotating Drivelines
Use Steps and Handholds Correctly
Read Operator’s Manuals for ISOBUS Controllers
Use Seat Belt Properly
Operating the Tractor Safely
Avoid Backover Accidents
Limited Use in Forestry Operation
Operating the Loader Tractor Safely
Keep Riders Off Machine
Instructional Seat
Use Safety Lights and Devices
Use a Safety Chain
Transport Towed Equipment at Safe Speeds
Use Caution on Slopes, Uneven Terrain, and Rough Ground
Freeing a Mired Machine
Avoid Contact with Agricultural Chemicals
Handle Agricultural Chemicals Safely
Handling Batteries Safely
Avoid Heating Near Pressurized Fluid Lines
Remove Paint Before Welding or Heating
Handle Electronic Components and Brackets Safely
Practice Safe Maintenance
Avoid Hot Exhaust
Clean Exhaust Filter Safely
Work In Ventilated Area
Support Machine Properly
Prevent Machine Runaway
Park Machine Safely
Transport Tractor Safely
Service Cooling System Safely
Service Accumulator Systems Safely
Service Tires Safely
Service Front-Wheel Drive Tractor Safely
Tightening Wheel Retaining Bolts/Nuts
Avoid High-Pressure Fluids
Do Not Open High-Pressure Fuel System
Store Attachments Safely
Decommissioning — Proper Recycling and Disposal of Fluids and
Components
00B - Safety Signs
Replace Safety Signs
DANGER
DANGER
WARNING
WARNING
CAUTION
WARNING
WARNING
CAUTION
CAUTION
WARNING
CAUTION—Cab Tractors
10 - Controls and Instruments
Front Console Controls
Foot Operated Controls
Right-Hand Console Controls
Left-Hand Console Controls
Fender Controls
HVAC Controls
Instrument Panel
Information Display and Display Mode Switch
Information Display
20 - Engine Operation
Use Key Switch
Using Throttle
Using eThrottle—If Equipped
Starting the Engine—Hydrostatic Transmission
Starting the Engine—PowrReverser Transmission
Stopping Machine
30 - Air Intake, Fuel, Coolant, and Exhaust Operation
Using Fuel Shutoff Valve
Filling Fuel Tank
Exhaust Filter System Overview
40 - Electrical and Lighting Operation
Use Lights and Turn Signals
Use Display Mode Switch
Using Dome Light—Cab
Using Power Port Outlet
50 - Drivetrain Operation
Drive Machine—Hydrostatic Transmission
Driving Machine—PowrReverser Transmission
50A - Transmission Operation
Operating Hydrostatic Transmission
Operating PowrReverser Transmission
Use PowrReverser Shuttle Control—If Equipped
Using Cruise Control—If Equipped
Using LoadMatch—(4044M, 4052M, 4066M)
Using LoadMatch—(4044R, 4052R, 4066R)
Using SpeedMatch—If Equipped
Using MotionMatch—(4044M, 4052M, 4066M)
Using MotionMatch—(4044R, 4052R, 4066R)
50B - MFWD and Front Axle Operation
Using Mechanical Front Wheel Drive (MFWD)
50C - Differential and Rear Axle Operation
Using Differential Lock (Traction Assist)
50D - Power Take Off (PTO) Operation
Stay Clear of Rotating Drivelines
Using the Power Take-Off (PTO) Safely
Using Rear PTO Switch
Using the Two Speed Rear PTO—If Equipped
60 - Steering and Brake Operation
Use Brake Pedals
Use Park Brake
Adjusting Tilt Steering Wheel—If Equipped
70 - Hydraulics Operation
Warm Hydraulic System Oil
Hydraulics Information
70A - Hitch and Drawbar Operation
Operate Attachments
Using Hitch Assist—If Equipped
Using Drawbar Hitch—If Equipped
Use 3-Point Hitch
Use Rockshaft Control Lever
Use Rate-of-Drop
Level Hitch
Adjust Hitch Side Sway
Using Optional iMatch Quick-Attach Hitch System
Using Front 3-Point Hitch—If Equipped
Using Front Hitch Lift Arms—Category 1—If Equipped
Using Loader with Front Hitch—If Equipped
Using Torsion Tube—Category 1—If Equipped
Using Heavy Duty Push Bar—Category 1—If Equipped
70B - Selective Control Valve Operation
Avoid High-Pressure Fluids
Connecting Implement Hydraulic Hoses
Using Dual Selective Control Valve Lever—If Equipped
Using 3rd Selective Control Valve (SCV) Outlet—If Equipped
Using Power Beyond Outlet—If Equipped
Using IV and V Rear Outlet Selective Control Valve (SCV)—If
Equipped
Using Diverter I, II, and III Rear Outlets—If Equipped
80 - Wheels and Tires Operation
Tire Combinations
80A - Ballast
Selecting Ballast
Ballast Machine
Implement Codes
Use Optional Rear Cast Iron Wheel Weights
Use Optional Rear Ballast Box
Use Liquid Weight in Tires
Use Optional Front Weights
80B - Additional Equipment Operation
Additional Equipment Operation
90 - Operator Station Operation
Entering and Exiting Machine
Adjusting Seat
Using Seat Belt
Raising and Lowering Roll-Over Protective Structure (ROPS)
HVAC Temperature Control—Cab
Using Windshield Wiper and Washer—Cab
Defrost Windshield and Side Glass—Cab
Using Radio—Cab
Using Rear Window—Cab
Using Toolbox—If Equipped
100 - Transport and Storage
Transport Machine on Trailer
Transporting Machine
Pushing or Towing Machine
Towing Loads
Safety Chain
Store Safety
Prepare Machine for Storage
Prepare Fuel and Engine For Storage
Remove Machine from Storage
Placing Front Hitch Lift Arms in Storage Position—Category 1—If
Equipped
200 - Maintenance Intervals
Service Your Machine
Maintenance Interval Chart—Daily to Every 400 Hours
Maintenance Interval Chart—Every 400 Hours or Annually to Every
6000 Hours
Test Safety Systems
Testing Rear PTO Switch
Testing the Seat Switch
Avoid Damage to Plastic and Painted Surfaces
Clean Plastic Surfaces
Clean and Repair Metal Surfaces
200A - Fuel, Lubricants, and Coolant
Diesel Fuel
Handling and Storing Diesel Fuel
Testing Diesel Fuel
Minimizing the Effect of Cold Weather on Diesel Engines
Alternative and Synthetic Lubricants
Engine Oil
Diesel Engine Coolant
Operating in Warm Temperature Climates
Additional Information About Diesel Engine Coolants and John
Deere COOL-GARD™ II Coolant Extender
Testing Diesel Engine Coolant
Testing Coolant Freeze Point
Transmission and Hydraulic Oil
Front Axle and MFWD Oil
Grease
200B - Maintenance—As Required
Service—As Required
210 - Controls and Instruments Maintenance
Controls and Instruments Maintenance
220 - Engine Maintenance
Required Emission-Related Information
Daily Startup Procedure
Avoid Fumes
Checking Engine Oil Level
Changing Engine Oil and Filter
Clean Dust Unloading Valve
Servicing the Alternator Belt
Servicing the Air Conditioner Belt—Cab
Clean Front Grille Screens
Checking Engine Oil Level
Changing Engine Oil and Filter
Cleaning Front and Side Grille Screens
Clean Engine Compartment
230 - Air, Fuel, Coolant and Exhaust Maintenance
Servicing Air Filter Elements
Checking Air Filter Intake Hose
Exhaust Filter Maintenance and Service
Automatic (AUTO) Exhaust Filter Cleaning
Disabled Exhaust Filter Cleaning
Parked Exhaust Filter Cleaning
Service Exhaust Filter Cleaning
Checking and Cleaning Fuel Filter Sediment Bowl and Replacing
Filter
Fuel Injection Pump
Fuel Injection Nozzles
Service Cooling System Safely
Servicing Cooling System
Checking Radiator Hoses and Clamps
Cleaning Cooling Fins
240 - Electrical and Lighting Maintenance
Service Electrical
Service the Battery Safely
Check Battery Electrolyte Level
Removing and Installing Battery
Clean Battery and Terminals
Use Booster Battery
Replacing Headlight Bulb
Replacing Light Bulbs—Open Station
Replacing Light Bulbs—Cab
Replacing Relays and Fuses
250 - Drivetrain Maintenance
Drivetrain Maintenance
250A - Transmission Maintenance
Checking Transmission Oil Level
Changing Transmission Oil and Hydraulic Suction Oil Filter
250B - MFWD and Front Axle Maintenance
Checking Front Axle Oil Level
Changing Front Axle Oil
Adjusting Front Axle Thrust Bolt Torque
Lubricating Axle Trunnion
250C - Differential and Rear Axle Maintenance
Rear Axle
250D - Power Take Off (PTO) Maintenance
PTO Maintenance
260 - Steering and Brake Maintenance
Check and Adjust Toe-In
270 - Hydraulics Maintenance
Hydraulic Maintenance
270A - Hitch and Drawbar Maintenance
Lubricating 3-Point Hitch
270B - Selective Control Valve Maintenance
Check Selective Control Valve
280 - Wheels and Tires Maintenance
Checking Wheel Bolts and Hardware
Removing and Installing Wheels
Check Tire Pressure
Tire Inflation Pressure Chart
Select Front Tire Rolling Direction
Changing Wheel Spacing and Tread Width
Lifting Points for Jacking up the Tractor
Front and Rear Tire Capacity
280A - Ballasting Maintenance
Match Ballast to Work Load
280B - Additional Equipment Maintenance
Additional Equipment Maintenance
290 - Operator Station Maintenance
Raising and Lowering Hood
Side Panel Removal and Installation
Hood Cowl Removal and Installation
Cleaning Hood Vents
Inspect ROPS for Loose Hardware
Servicing Air Conditioner
Cleaning Cab Air Filter
Checking Cab Roll-Over Protection System Installation
300 - Troubleshooting
Engine
Electrical System
Heater and Air Conditioning System
Machine
Brakes
Steering
300A - On Board Diagnostics
Service Alert and Information Display
On Board Diagnostic Display
On-Board Diagnostic (OBD) Tool
Diagnostic Trouble Code (DTC)
Come Home Mode
400 - Specifications
Engine Specifications
Drivetrain Specifications
Hydraulic System Specifications
Electrical System Specifications
Fluid Capacities
Ground Speeds
Dimensions
Height From Ground
Ground Clearance
Track Width
Turning Radius
Machine Weight
3-Point Hitch Specification
How to Calculate Maximum Permissible Download on Trailer Hitch
How to Calculate Permissible Mass
Unified Inch Bolt and Screw Torque Values
Metric Bolt and Screw Torque Values
400A - Identification Numbers
Product Identification Information
Record Identification Numbers
400B - Certification and Warranty
Product Warranty
John Deere, California and U.S. EPA Emission Control System
Warranty (Non-Road Diesel)
Tire Warranty
Limited Battery Warranty
500 - Service Records
Every 10 Hour Service
Every 50 Hour Service
Every 100 Hour Service
Every 200 Hour Service or Annually
Every 400 Hour Service
Every 400 Hour Service or Annually
Every 600 Hour Service
Annually
Every 1000 Hour Service
Every 2000 Hour Service or Every Two Years
Every 6000 Hour Service or Every Six Years
Change of Ownership
Change of Ownership
Change of Ownership
JDS - John Deere Service
John Deere Is At Your Service
Technical Information