630C, 640C and 645C Windrow Pickups
Copyright 2009 (c) Deere & Company. THIS DATA IS THE PROPERTY OF DEERE & COMPANY. ALL USE AND/OR REPRODUCTION NOT SPECIFICALLY AUTHORIZED BY DEERE & COMPANY IS PROHIBITED.
All information, illustrations and specifications in this manual are based on the latest information available at the time of publication. The right is reserved to make changes at any time without notice.
Foreword
Dealer's Record
Predelivery Inspection
Section : 00 - Identification View
Identification View
Section : 05 - Safety
Recognize Safety Information
Follow Safety Instructions
Understand Signal Words
Observe Road Traffic Regulations
Store Attachments Safely
Prepare for Emergencies
Wear Protective Clothing
Check Machine Safety
Guards and Shields
Use Safety Lights and Devices
Operate Pickup Safely
Stay Clear of Rotating Drivelines
Practice Safe Maintenance
Avoid High-Pressure Fluids
Service Tires Safely
Use Proper Tools
Service Machines Safely
Support Machine Properly
Stay Clear of Pickup
Transport with Harvesting Unit Installed
Ballasting for Safe Ground Contact
Remove Paint Before Welding or Heating
Avoid Heating Near Pressurized Fluid Lines
Avoid High-Pressure Jet on Safety Decals
Dispose of Waste Properly
Section : 10 - Safety Decals
Pictorial Safety Signs
Operator's Manual
Repair and Maintenance
Windrow Pickup
Height Adjustable Compression Device
Compression Device Safety Lock
Hydraulic Lines
Stay Clear of Rotating Driveline
Pickup Wheels
Accumulator - Roller Compression Unit Float System (Option)
Roller Compression Unit - Tips of Rake (Option)
Hydraulic System
Locking Oscillating Frame
Hanging Points
Section : 15 - Preparing the Pickup
Unpacking and First Setup
Set Gauge Wheel Height
Check Adjustment of Automatic Auger Lifting (Option)
Section : 20 - Preparing the 6000 and 7000 Harvesters
Before Attaching the Pickup on 7000 Series Harvesters
Before Attaching the Pickup on 6000 Series Harvesters
Section : 25 - Attaching
Adjusting Channel Width
Attaching the 630C Pickup with Rigid Frame
Adjusting Pickup Attaching Hole Supports (630C with Rigid Frame)
Attaching the 630C Pickup with Oscillating Frame
Adjusting Pickup Attaching Hole Supports (630C with Oscillating Frame)
Attaching the 640C and 645C Pickups
Adjusting Pickup Attaching Hole Supports (640C and 645C)
Connecting Hydraulic Hoses
Section : 30 - Detaching
Detaching the 630C Pickup
Detaching the 640C and 645C Pickups
Section : 35 - Transporting the Pickup
Observe Public Road Legislation
Locking Oscillating Frame (if equipped)
Setting Crop Deflector in Transport Position
Setting Gauge Wheels in Transport Position
Setting Roller Compression Unit in Transport Position (Option)
Section : 40 - Operating the Pickup
Follow Safe Operating Procedures
Working Under A Raised Roller Compression Unit (Option)
Unlocking Oscillating Frame (if equipped)
Setting Gauge Wheels in Operating Position
Setting Crop Deflector in Operating Position
Adjusting Crop Deflector
Adjusting Crop Deflector Working Height
Adjusting Crop Deflector Sheet Angle
Setting Roller Compression Unit in Operating Position (Option)
Operating the Roller Compression Unit (Option)
Adjusting Deflector Plate of Roller Compression Unit (Option)
Adjusting Rake of Roller Compression Unit (Option)
Adjusting Gauge Wheel Height
Adjusting the Pickup Float
Adjusting Compensating Spring for Oscillating Frame (if equipped)
Adjusting Feed Auger Height
Adjusting Feed Auger Springs
Adjusting the Scrapers
Adjusting Automatic Auger Lifting (Option)
Adjusting Feed Auger Speed
Opening the Side Guard
Adjusting Feed Auger Retractable Fingers (if equipped)
Adjusting Feed Auger Paddles (if equipped)
Adjusting the Stone Trap
Section : 45 - Attachments
Top Flight Reinforcement Kit
Special Kit for Feed Auger Drive High Speed
Roller Compression Unit
Automatic Auger Lifting
Section : 50 - Lubrication and Maintenance
Lubrication Intervals
Grease
Gear Oil
Alternative and Synthetic Lubricants
Lubricant Storage
Mixing of Lubricants
Every 10 Hours - 630C Pickup Drive Shaft
Every 10 Hours - 640C and 645C Pickup Drive Shaft
Every 10 Hours - Drive Chains
Every 50 Hours - Pivoting Gauge Wheels
Every 50 Hours - Lift Arms of Roller Compression Unit (Option)
Every 50 Hours - Feeding Auger Pivot Points
Every 50 Hours - Oscillating Frame Pivot (if equipped)
Every 500 Hours - Gear Case
Section : 55 - Troubleshooting
Pickup Operation
Section : 60 - Service
Metric Bolt and Screw Torque Values
Adjusting the Drive Chains
Feeding Auger Rubber Stops
Adjusting Deflector Compensating Springs
Windrow Pickup Hanging Points
Section : 65 - Storage
Storing the Pickup
Taking the Pickup out of Storage
Section : 70 - Specifications
630C Pickup
640C Pickup
645C Pickup
Declaration of Conformity
EC Declaration of Conformity
Section : 75 - Serial Number
Serial Number
Pickup Serial Number Plate (Up to Construction Year 2009)
Pickup Serial Number Plate (From Construction Year 2010)
Record Pickup Serial Number
Keep Proof of Ownership
Keep Machines Secure
Section : IBC - John Deere Service Keeps You On The Job
John Deere Parts
The Right Tools
Well-Trained Technicians
Prompt Service