625D, 630D, and 635D Draper Platforms
Copyright 2008 (c) Deere & Company. THIS DATA IS THE PROPERTY OF DEERE & COMPANY. ALL USE AND/OR REPRODUCTION NOT SPECIFICALLY AUTHORIZED BY DEERE & COMPANY IS PROHIBITED.
All information, illustrations and specifications in this manual are based on the latest information available at the time of publication. The right is reserved to make changes at any time without notice.
Foreword
Section : 05 - Safety
Platform Safety Features
Safety Sign Location
Recognize Safety Information
Understand Signal Words
Use Safety Lights and Devices
Follow Safety Instructions
Spanish Safety Signs and Operator's Manual
Wear Protective Clothing
Prepare for Emergencies
Store Attachments Safely
Road Transport Disconnect Switch
Guards and Shields
Stay Clear of Harvesting Units
Keep Hands Away From Knives
Stay Clear of Rotating Drivelines
Ballasting for Safe Ground Contact
Practice Safe Maintenance
Service Machines Safely
Support Machine Properly
Park Machine Safely
Avoid Contact With Moving Parts
Avoid Contact With Cutterbar
Service Belts Safely
Transport Safely
Observe Maximum Transport Speed
Service Tires Safely
Avoid High-Pressure Fluids
Remove Paint Before Welding or Heating
Protect Against High Pressure Spray
Avoid Heating Near Pressurized Fluid Lines
Dispose of Waste Properly
Replace Safety Signs
Section : 10 - Transporting
Transporting
Preparing Platform for Transport (If Equipped with Slow Speed Integral Transport System)
Preparing Platform for Field Operation (If Equipped with Slow Speed Integral Transport System)
Section : 15 - Attaching and Detaching
Attaching Platform to Combine
Detaching Platform from Combine
Feeder House Manual Unlatching
Replacement Shear Screw Location
Section : 20 - Calibration and Programing
When to Calibrate
Calibration Error Codes
Active Header Control Display
Automatic Header Height Control System
Section : 25 - Operating the Platform
General Information
Armrest Functions
Draper Belt Speed
Draper Belt Speed Adjust Switch (If Equipped)
Setting Backshaft Speed
Cutterbar Tilt Adjust Switch (If Equipped)
Reel Settings
Feed Drum Settings
Automatic Header Height Control
Recommended Combine Settings
Recommended Initial Crop Settings
Harvesting in Dry Crop Conditions
Harvesting in Tough Feeding Crop Conditions
Harvesting in Short, Thin Crops
Harvesting in Down Crops
Bushy or High Volume Crops
Sorghum
Seed Loss Chart
Section : 30 - Attachments and Options
Feeding Auger
Long Divider Points
Knife Guards (4 in.)
Plastic Skid Shoes
Crop Lifters
Crop Lifter Adjustments
Reel End Fingers
Section : 35 - Adjustments - Suspension and Leveling
Leveling Draper Cutterbar to Ground
Equalize the Float System
Lock and Unlock the Float System
Lock and Unlock Gauge Wheels (If Equipped)
Section : 40 - Adjustments - Feeding Related
Platform Adjustment-Feeding
Cutterbar Tilt
Feed Drum Finger Timing
Side Draper Belt Tension
Center Draper Belt Tension
Knife Hold-Down Clearance
Section : 45 - Adjustments - Windrow Conversion
Removing Center Feed Assembly
Section : 50 - Adjustments - Reel
Set Reel Safety Stops
Minimum Reel Height and Leveling Reel
Rephase and Bleed Lift Cylinders
Finger Pickup Settings
Hydraulic Adjustment of Fore/Aft
Fore/Aft Cylinder Mount Adjustments
Speed Ratio Sensor Adjustment
Adjust Reel Drive Gear
Section : 55 - Lubrication
Lubrication
Lubricant Storage
Alternative and Synthetic Lubricants
Lubrication Interval Chart
Every 50 Hours of Operation
Every 200 & 400 Hours of Operation
Section : 60 - Maintenance
Feeder House Safety Stop
Open Side Shields
Remove and Install Side Shields
Remove and Install Backshaft Drive Belts
Remove and Install Telescoping Knife Drive Shaft
Cutterbar Maintenance
Knife Section Service Kit
Remove and Install Cutterbar Knife
Remove and Install Knife Sections
Align Knife Head and Knife Drive
Spare Knife Storage
Remove and Install Knife Guards
Center Draper Cleanout
Cleaning Material Build Up at Side Shields
Remove and Install Side Draper Belts
Remove and Install Center Draper Belt
Remove and Install Feed Drum Finger Guides
Remove and Install Feed Drum Fingers
Header Warning Light Bulb Replacement
Remove and Install Sump Pan
Removing Center Feed Assembly
Section : 65 - Storage
End of Season Service
Beginning of Season Service
Section : 70 - Troubleshooting
Cutting Platform
Section : 75 - Specifications
Overall Dimensions
Gauge Wheel Tire Pressure
Cutterbar
Platform Weights
Header Identification Number
Keep Machines Secure
Keep Proof of Ownership
Metric Bolt and Screw Torque Values
Unified Inch Bolt and Screw Torque Values
Section : JDSLA - John Deere Service Literature Available
Technical Information
Section : IBC - John Deere Service Keeps You On The Job
John Deere Is At Your Service