H240, H260, H310, H340, H360, and H380 Loaders
Copyright 2013 © Deere & Company. THIS DATA IS THE PROPERTY OF DEERE & COMPANY. ALL USE AND/OR REPRODUCTION NOT SPECIFICALLY AUTHORIZED BY DEERE & COMPANY IS PROHIBITED.
All information, illustrations and specifications in this manual are based on the latest information available at the time of publication. The right is reserved to make changes at any time without notice.
Foreword
Predelivery Inspection
Section 05 - Identification Views
H240, H260, H310, H340, H360 and H380 Loader Identification
View
Section 10 - Safety
Recognize Safety Information
Understand Signal Words
Follow Safety Instructions
Wear Protective Clothing
Check Machine Safety
Protect People and Animals
Operating the Loader Tractor Safely
Avoid Injury or Death from Rollover Accidents
Operating Non-Self-Levelling Loaders
Australian Code of Practice
Avoid Injury or Death from Falling Loads
Operate Loader with Attachments from Other Manufacturers
Avoid Power Lines
Dig Safely
Detach Loader Safely
Use Safety Lights and Devices
Service Loader Safely
Service Machines Safely
Practice Safe Maintenance
Store Attachments Safely
Avoid Heating Near Pressurized Fluid Lines
Avoid High-Pressure Fluids
Service Accumulator Systems Safely
Relieve Hydraulic Pressure Safely
Remove Paint Before Welding or Heating
Dispose of Waste Properly
Avoid High-Pressure Jet on Safety Signs
Avoid High-Pressure Jet on Cylinders
Section 15 - Safety Signs
Pictorial Safety Signs
Replace Safety Signs
Operator’s Manual
Protect People and Animals
Avoid Injury or Death from Falling Load
Falling Round Bales
Avoid Injury or Death from Electric Line Contact
Shock Absorbers
Hydraulic Implement Unlatching
Operator's Warning Decal (Australia only)
Avoid Injury or Death from Falling Loader (Australia Only)
Section 20 - Abbreviations
Abbreviations
Tractor Engine Emission Level
Section 25 - Application Charts
H240 Loader: Approved MFWD Tractors, Rear Ballast and Approved
Front Tires
H240 Loader: Approved 2WD Tractors, Rear Ballast and Approved
Front Tires
H260 Loader: Approved MFWD Tractors, Rear Ballast and Approved
Front Tires
H260 Loader: Approved 2WD Tractors, Rear Ballast and Approved
Front Tires
H310 Loader: Approved MFWD Tractors, Rear Ballast and Approved
Front Tires
H310 Loader: Approved 2WD Tractors, Rear Ballast and Approved
Front Tires
H340 Loader: Approved MFWD Tractors, Rear Ballast and Approved
Front Tires
H340 Loader: Approved 2WD Tractors, Rear Ballast and Approved
Front Tires
H360 Loader: Approved MFWD Tractors, Rear Ballast and Approved
Front Tires
H360 Loader: Approved 2WD Tractors, Rear Ballast and Approved
Front Tires
H380 Loader: Approved MFWD Tractors, Rear Ballast and Approved
Front Tires
Section 30 - Prepare the Tractor
Adjust Flow Rate and Timed Detent of Tractor SCVs and ICVs
Checking Front Tire Pressure
Checking Front Wheel Bolts
Remove Front Weights
Adjust Front Tread (5020, 5E, 5G, 5M, 5R, 6000, 6010, 6020,
6D, 6MC and 6RC Series Tractors)
Adjust Front Tread (6025, 6030, 6M and 6R Series 4-Cylinder
Tractors)
Adjust Front Tread (6025, 6030, 6M, 6R, 6RE and 7030 Series
6-Cylinder Tractors)
Adjust Rear Tread of Tractor
Ballast Tractor with Loader
Section 32 - Break-In Period
Checking Front Wheel Bolts
Check Mounting Frame Hardware
Section 35 - Controls
Loader Control Levers
Operate 3rd and 4th Functions with 2-Function Independent Control
Valve and Diverter
Operate 3rd and 4th Functions with 3-Function Independent Control
Valve
Operating 3rd and 4th Functions with Armrest-Integrated Multi-Function
Lever
Gearshift Switches on the Multi-Function Lever (Tractor with
PowrQuad™ PLUS, AutoQuad™, and PowrReverser™ Plus
Transmission)
Operate MEMOSYSTEM (if equipped)
Operate Return-to-Position Function (if equipped)
Section 40 - Attach and Detach Loader
Attach Loader
Detach Loader
Section 45 - Attach and Detach Bucket or Attachment
Attach Bucket or Attachment
Detach Bucket or Attachment
Section 50 - Transport
Keep Riders Off Machine
Carry Loads
Driving on Public Roads
Section 55 - Operate Loader
Loader Operation Speed Limit
Park Tractor with Loader Attached
Operate Lift Cylinder Mechanical Locks (Australia Only)
Operate Electrical Shut-Off Device (if Equipped)
Raise and Lower Loader
Loader Suspension System
Remove Material from a Pile
Dig
Attachment Level Indicator (MSL and NSL Loaders)
Attachment Level Indicator (Hydraulic Self-Leveling Loader)
Level and Scrape Forward
Level in Reverse
Dump Bucket
Section 60A - Operate Bale Fork and Bale Spike
Avoid Injury or Death from Rollover Accidents
Avoid Injury or Death from Falling Round Bales
Transport a Round Bale
Pick Up Round Bale with Round Bale Fork and Bale Spike
Pick Up Round Bale on a Slope with Round Bale Fork and Bale
Spike
Set Teeth Spacing on Bale Spike with Foldable Teeth
Put Bale Spike with Foldable Teeth in Transport or Working Position
Store Round Bale Fork
Store Bale Spike with Foldable Teeth
Section 60B - Operate Bale Grapple and Bale Gripper
Avoid Injury or Death from Rollover Accidents
Avoid Injury or Death from Falling Round Bales
Transport a Round Bale
Set Heavy-Duty Multiple Bale Grapple Frame Position for ISO
or Combi ISO/SMS and ISO/MX Carrier
Install and Remove Heavy-Duty Multiple Bale Grapple Inferior
Teeth
Handle Bale with Heavy-Duty Multiple Bale Grapple
Operate the Round Bale Grapple and Gripper
Handle Round Bale by Its Curved Surface
Handle Round Bale by Its Ends
Store the Round Bale Grapple and Gripper
Section 60C - Operate Bale Elevator
Avoid Injury or Death from Rollover Accidents
Avoid Injury or Death from Falling Round Bales
Transport a Round Bale
Operate the Round Bale Elevator
Handling Round Bale by Its Curved Surface
Handling Round Bale by Its Ends
Storing the Round Bale Elevator
Section 65 - Attachments
Standard Bucket
Earth Bucket
Heavy-Duty Bucket
Replaceable Cutting Edge
Digging Teeth
High-Volume Bucket
Grain Bucket
Standard Multi-Purpose Bucket
Heavy-Duty Multi-Purpose Bucket
Grapple for Heavy-Duty Multi-Purpose Bucket
Standard Manure Fork
Standard Manure Fork with Grapple
Heavy-Duty Manure Fork
Heavy-Duty Manure Fork with Grapple
Pallet Fork
Bale Spike
Combi Frame Pallet Fork and Bale Spike
Bale Spike with Foldable Teeth
High Capacity Bale Grapple
Heavy-Duty Multiple Bale Grapple
Articulated Bale Gripper
Round Bale Elevator
Roll Back Kit
Rear Ballast Box
Tractor Hood Guards
Section 70 - Lubrication and Maintenance
Lubricate and Maintain Loader Safely
Perform Lubrication and Maintenance
Observe Lubrication Symbols
Grease
Alternative and Synthetic Lubricants
First 3 Hours
First 10 Hours
As Required - Auto-Latch Device
Every 10 Hours - H310, H340 and H360 HSL Loaders
Every 10 Hours - H240, H260, H310, H340, H360 and H380 MSL Loaders
Every 10 Hours - H240, H260, H310, H340 and H360 NSL Loaders
Every 10 Hours - High Capacity and Heavy-Duty Multiple Bale
Grapple
Every 10 Hours - Articulated Bale Gripper
Every 10 Hours - Round Bale Elevator
Every 10 Hours - Heavy-Duty Manure Forks with Grapple
Every 10 Hours - Standard Manure Forks with Grapple
Every 10 Hours - Standard Multi-Purpose Bucket
Every 10 Hours - Heavy-Duty Multi-Purpose Bucket with Grapple
Every 50 Hours - Check Mounting Frame Hardware (5020 Series
Tractors)
Every 50 Hours - Check Mounting Frame Hardware (5E Series 3-Cylinder
Tractors)
Every 50 Hours - Check Mounting Frame Hardware (5E Series 4-Cylinder
Tractors)
Every 50 Hours - Check Mounting Frame Hardware (5G Series Tier
3 Tractors)
Every 50 Hours - Check Mounting Frame Hardware (5G Series iT4
Tractors)
Every 50 Hours - Check Mounting Frame Hardware (5M Series Tier
3 and iT4 PIN Prefix 1LV Tractors)
Every 50 Hours - Check Mounting Frame Hardware (5M and 5R Series
PIN Prefix 1L0 Tractors)
Every 50 Hours - Check Mounting Frame Hardware (6000, 6010,
6020, 6025 and 6030 Series 4-Cylinder Tractors)
Every 50 Hours - Check Mounting Frame Hardware (6D Series Tier
3 Tractors)
Every 50 Hours - Check Mounting Frame Hardware (6D Series iT4
Tractors)
Every 50 Hours - Check Mounting Frame Hardware (6M, 6MC, 6R
and 6RC Series 4-Cylinder Tractors)
Every 50 Hours - Check Mounting Frame Hardware (6000, 6010,
6020, 6025, 6030, 7030, 6M, 6R and 6RE Series 6-Cylinder Tractors)
Every 100 Hours - Return-to-Position Potentiometer
Every 100 Hours or Monthly - Hydraulic Hoses
Every 3 Years - Accumulators
Every 6 Years - Hydraulic Hoses
Every 10 Years - Accumulators
Section 75 - Troubleshooting
Hydraulic System Troubleshooting
Bucket Troubleshooting
Mast Pin Troubleshooting
Section 80 - Service
Service Loader and/or Tractor Safely (Loader Attached - Except
Australia)
Service Loader and/or Tractor Safely (Loader Attached - Australia
Only)
Shut-Off Valve
Keep Service Area Clean
Avoid High-Pressure Fluids
Metric Bolt and Screw Torque Values
Unified Inch Bolt and Screw Torque Values
Suspension System Service
Adjust MEMOSYSTEM Sensor
Access Front of Tractor (if Equipped with Foldable Hood Guard)
Identify Hose Connections—2-Function Loader with Multicoupler
Identify Hose Connections—3-Function Loader with Multicoupler
Identify Hose Connections—Mid-Mount Couplers
Hydraulic Connections: Multicoupler for 3rd Function
Hydraulic Connections: Multicoupler for 3rd Function and Individual
Couplers for 4th Function
Hydraulic Connections: MEMOSYSTEM Valve for 2-Function Loader
Hydraulic Connections: MEMOSYSTEM Valve for 3-Function Loader
Loader Hanging Points (H240 and H260 Loaders)
Loader Hanging Points (H310, H340, H360 and H380 Loaders)
Section 85 - Storage
Prepare Loader for Storage
Store Loader and Attachments
Section 90 - Specifications
Rated Operating Load
Record Tractor Information (Australia Only)
Specification Parameters
H240 NSL Loader Specifications on 5075E Tractor1
H240 MSL Loader Specifications on 5075E Tractor1
H260 NSL Loader Specifications on 5115M iT4 Tractor1
H260 MSL Loader Specifications on 5115M iT4 Tractor1
H310 NSL Loader Specifications on 6125R Tractor1
H310 MSL Loader Specifications on 6125R Tractor1
H310 HSL Loader Specifications on 6125R Tractor1
H340 NSL Loader Specifications on 6125R Tractor1
H340 MSL Loader Specifications on 6125R Tractor1
H340 HSL Loader Specifications on 6125R Tractor1
H360 NSL Loader Specifications on 6210R Tractor1
H360 MSL Loader Specifications on 6210R Tractor1
H360 HSL Loader Specifications on 6210R Tractor1
H380 MSL Loader Specifications on 6210R Tractor1
Section 95 - Serial Number
Serial Number Plate Description
Record Serial Number
Keep Proof of Ownership
Keep Machines Secure
Section 100 - EC Declaration of Conformity
CE Conformity Marking
EC Declaration of Conformity
EC Declaration of Conformity
EC Declaration of Conformity
EC Declaration of Conformity
EC Declaration of Conformity
EC Declaration of Conformity
EC Declaration of Conformity
EC Declaration of Conformity
EC Declaration of Conformity
Section IBC - John Deere Service Keeps You On The Job
John Deere Parts
The Right Tools
Well-Trained Technicians
Prompt Service