1910 Commodity Air CartA01910T735101A01910H735101
Copyright 2009 (c) Deere & Company. THIS DATA IS THE PROPERTY OF DEERE & COMPANY. ALL USE AND/OR REPRODUCTION NOT SPECIFICALLY AUTHORIZED BY DEERE & COMPANY IS PROHIBITED.
All information, illustrations and specifications in this manual are based on the latest information available at the time of publication. The right is reserved to make changes at any time without notice.
Foreword
Section : 05 - Safety
Recognize Safety Information
Understand Signal Words
Follow Safety Instructions
Keep Riders Off Machine
Hydraulic Hose Replacement
Practice Safe Maintenance
Prepare for Emergencies
Wear Protective Clothing
Handle Agricultural Chemicals Safely
Use Safety Lights and Devices
Use a Safety Chain
Tow Loads Safely
Observe Maximum Transport Speed
Avoid High-Pressure Fluids
Remove Paint Before Welding or Heating
Avoid Heating Near Pressurized Fluid Lines
Dispose of Waste Properly
Store Attachments Safely
Stay Clear of Air Hoses
Use a Signal Person
Park Safely
Transport Safely
Transport Safely (Continued)
Operation in Hilly Conditions and Addition of Ballast-1690 and 1890 Single Rank
Keep Shields in Place
Use Handholds and Steps
Follow Safe Operating Procedures
Safety Signs
Section : 10 - General Information
Use Tractor and Seeding Tool Operator's Manuals
Air Cart/Seeding Terms and Definitions
Configuration Identification
Section : 15 - Prepare Tractor
Use Tractor Operator's Manual
Recommended Tractors
Calculating Minimum Tractor Weight for Safe Transport
Calculate Minimum Tractor Weight For Safe Transport-Chart
Determine Tractor Requirements
Determine Tractor Drawbar and Implement Clevis Compatibility
Raise and Lock 3-Point Hitch
Position Drawbar
Use a Drawbar Support
Use a Safety Chain
Low Pressure Case Drain Connection
Powering Cart Clutches and Lights
Section : 20 - Prepare Machine
Prepare and Lubricate 1910 Commodity Air Cart
Install Proper Drawbar Clevis
Level Tow-Between Cart
Change Rear Tires
Change Seeding Equipment, Row Spacing or Product
Change Row Spacing
Determine Tow-Behind (TBH) Commodity Cart and Implement Compatibility
Section : 25 - Attach and Detach
Use Tractor and Seeding Tool Operator's Manuals
Attach Safety Chains
Make Proper Hose Connections
Attach Seeding Tool or Air Cart to Tractor
Attach Seeding Tool to Tow-Between Cart
Tow-Behind Field Hitch
Attach Tow-Behind Cart to Air Seeder
Connecting Optional Blockage Warning-Seed Counting Wiring Harness (If Equipped)
Open and Close Hydraulic Lock-Up Valve
Checking Hydraulic Control Functions
Detach Machine From Tractor
Detach Seeding Tool From Tow-Between Cart
Detach Tow-Behind Cart From Seeding Tool
Tow-Behind Cart Rear Hitch- Attachment
Tow-Behind Cart Rear Hitch Warning Light Harness Attachment
Hand Signals
Section : 30 - Transport
Attach Safety Chains
Use Warning Lights and SMV
Keep Riders Off Machine
Observe Maximum Transport Speed
Transport Safely
Positioning Tractor Drawbar for Transport
Lock Up Depth Control
Disengage Main Clutch for Transport
Transport Speed Explanation
Use Tow-Behind Cart Yard Hitch
Transport Tow-Behind Cart with Rear Attached Implement
Reduce Tow-Behind Cart Transport Weave
Operation or Transport on Hillsides
Operation or Transport On Hillsides (Continued)
Operate 1690 and 1890 in Hilly Conditions and Addition of Ballast
Section : 35 - How to Use Monitor
Use with GreenStar™ Monitors
Monitor Controls
Monitor Power Up and Power Down
Standard Buttons
Input Entry Methods
Screen Navigation
Section : 40 - Monitor Settings
Configure Brightness, Volume, and Color
Configure Language and Units of Measure
Configure Date and Time
Touchscreen Calibration
Section : 45 - Performance Monitor
Check Implement Width in Performance Monitor
Radar Configuration
Radar Calibration
Section : 50 - Quick Set Guide
General Guidline
Start of Season Guide
Section : 55 - Monitor Setup for Air Cart
Configure Air Cart Size and Drive Sprockets
Configure Meter Drive Type and Remote Switch
Configure John Deere™ Seeding Tool
Configure Custom Seeding Tool
Configure Tire Speed Sensor
Configure Common Start and Stop Height
Configure Separate Start and Stop Height
Product Selections
Set Rate and Configure Tank Meters
Configure Variable Rates
Set Fan Speed
Run Screen for Variable Rate Cart
Run Screen for Fixed Rate Cart
Section : 60 - Monitor Setup for Blockage System
Adjust Sensor Sensitivity
Configure 1890 with Dual Row Spacing
Configure 2510S Strip Till Applicator
Configure All Other Seeding Tools
Run Screen for Blockage
Section : 65 - Operate Machine-General
Guidelines for Operation
Operational Checklist
Initial Field Check
Hillside Operation
Section : 70 - Meter Setup and Operation
Connect Main Clutch Power Jumper (Limp Home Feature)
Operating Half-Width Disconnects
Remove Meter Cartridge Assembly
Install Meter Cartridge Assembly
Interchangeable Meter Cartridge Assemblies
Adjust Agitator Shaft Action
Meter Cleanout Procedure
When to Change Active Meter Segments and Agitators
How To Change Meter Rollers
Tune Meter Segment Output to Tower Size
Meter Cartridge/Seeding Tool Diagrams
Open or Close Product Runs
Agitator Installation, Activation, and Deactivation
Active Meter Guide
Section : 75 - Air System Setup and Operation
Air System Description
Systematic Approach to Air Run Identification
Understand Air Velocity and Hose Routes
Tank Open Indicator Gauge
Operating 19 cm (7.5 in.) or 38 cm (15 in.) Dual Row Spacing Option (1690/1890 No-Till Air Drill Only)
Switch Row Spacings (1860/1890 No-Till Air Drill Only)
Setting Fan/Auger Selector Valve
Adjusting Double-Shoot Damper
Inspect Air System Seals, Hoses, and Header Rings
Adjust Tank Lid Down Pressure and Centering Tabs
Clean Fan Intake Screen
Switching Stationary Double-Shoot From Top-Shoot To Bottom-Shoot
Adjusting Stop Slide Bracket
Reconfiguring Stationary Double-Shoot Manifold
Section : 80 - Meter Calibration and Rate Verification
Meter Calibration
Meter Verification
Field Method for Meter Verification
Stationary Method for Meter Verification
1/10 Hectare Stationary Method or Meter Verification
1/10 Acre Stationary Method of Meter Verification
Section : 85 - Warning and Information Screens
Warning Messages
Information Messages
Section : 90 - Rate Charts
Adjust Rate Based On Seed Germination
Adjust Rate Based On Wear Plate
Population Rate Chart Based On Seeds Per Kilogram
Population Rate Chart Based On Seeds Per Pound
Sunflower Population Rate Chart Based On Seeds Per Kilogram
Sunflower Population Rate Chart Based On Seeds Per Pound
Kilograms of Soybean Seeds Per Hectare
Pounds of Soybean Seed Per Acre
Soybean Seeds Per Meter Per Row
Soybean Seeds Per Foot Per Row
Custom or Unlisted Products
Set Front and Rear Tanks to Empty Simultaneously (kg/hectare)
Set Front and Rear Tanks to Empty Simultaneously (lbs/acre)
Understand Meter Settings
How to Use Volume Rate Charts
Volume Rate Chart (Kilograms Per Hectare) with Low Rate (Yellow) Meter
Volume Rate Chart (Pounds Per Acre) with Low Rate (Yellow) Meter Roller
Volume Rate Chart (Kilograms Per Hectare) with Regular Rate (Black) Meter
Volume Rate Chart (Pounds Per Acre) with Regular Rate (Black) Meter Roller
Volume Rate Chart (Kilograms Per Hectare) with High Rate (Green) Meter
Volume Rate Chart (Pounds Per Acre) with High Rate (Green) Meter Roller
Volume Rate Chart (Kilograms Per Hectare) with Very High Rate (Blue) Meter
Volume Rate Chart (Pounds Per Acre) with Very High Rate (Blue) Meter Roller
Adjust Transmission Setting
Section : 95 - Conveyance System and Tank
Auger/Conveyor Precautions
Operating Tank Lids
Filling Tank to Capacity
Transporting Telescoping Spout
Tank Filling Indicator Lights
Field Lights
Adjusting Auger Hopper Position
Auger and Conveyor Arm Position Lock
Storage Position
Releasing From Storage Position
Filling Tank
Emptying Tank
Locking In Storage Position
Shortening Auger Outlet Hose
Section : 100 - Lubrication and Maintenance
Lubricating and Maintaining Machine Safely
Keep Shields In Place
Perform Lubrication and Maintenance Procedures
Grease
Transmission Oil
Alternative and Synthetic Lubricants
Lubricant Storage
Observe Lubrication Symbols
Before and After Each Season
Rear Wheel Bearing Maintenance
Lubricate Pivot Arm-10 Hours
Lubricate Agitator and Meter Shafts-50 Hours
Lubricate Roller Chains-50 Hours
Lubricate Caster Wheel and Front Beam Pivots (Tow-Behind)-50 Hours
Check Transmission Oil Level-Annually
Section : 105 - Air Cart Diagnostics
System Tests
Section : 110 - Blockage Diagnostics
System Status
Master Module Information
Member Module Information
Sensor Test
Section : 115 - Troubleshoot Air Cart
Troubleshooting Conveyance System
Troubleshoot Fan Assembly
Troubleshoot Air System
Troubleshooting Tank Lid Indicator Gauge
Troubleshoot Meter Drive System
Troubleshoot Product Meter System
Troubleshoot Blockage System
Troubleshoot General Monitor-Control Systems
Troubleshoot GreenStar™ Display
Troubleshoot Cart Controller
Section : 120 - Service
Detailed Service Information-Use TM2067
Using Safe Service Procedures
Keep Service Area Clean
Service and Operate Chemical Sprayers Safely
Prevent Machine Runaway
Metric Bolt and Screw Torque Values
Unified Inch Bolt and Screw Torque Values
Service Tires Safely
Correct Tire Mount
Repair Walking Wheels
Torque Hardware
Replace Tow-Behind Row Crop Caster Wear Pad
Check Tow-Behind Wheel Attachment Hardware and Bearings
Torque Rear Wheel Hardware
Replace Meter Drive Shear Pin
Adjust Meter Speed Sensor Gap
Check Meter Transmission Output
Replace and/or Adjust Fan Speed Sensor
Meter Cleanout Procedure
Clean Stationary Double-Shoot Air Chambers
Clean Meter Cartridge Assembly
Clean Manifold Air Passages-Every 50 Hours
Clean Lower Tank Lid Open Indicator Fitting-Every 15 Hours
Clean Tank Pressurization Lines-Every 50 Hours (Single-Shoot Only)
1910 Cart Single-Shoot Models
Tank Pressurization Hose Routing
1910 Cart Tow Between Models
Tank Pressurization Hose Routing
1910 Cart Tow Behind Models
Tank Pressurization Hose Routing
Adjust Conveyor Belt Tension and Tracking
Prevent Hydraulic System Contamination
Hydraulic Hose Diagram-Fan and Conveyance
Replace and/or Adjust Ground Speed Sensor
Electromagnetic Interference (EMI)
Section : 125 - Storage
Use Your Tillage Equipment Operator's Manuals
Preparing for Storage
Removing From Storage
Section : 130 - Specifications
Specifications-1910 Commodity Air Cart
Machine Weights
Tractor Hydraulic System Requirements
Tractor Hydraulic Compatibility
Tillage Compatibility Guide
Tire Inflation Pressures-195/250 Bushel Carts
Tire Inflation Pressures-270/340 Bushel Carts
Tire Inflation Pressures-350/430 Bushel Carts
Metric Conversion Factors
Declaration of Conformity
Declaration of Conformity
Declaration of Conformity
Declaration of Conformity
Record Machine Serial Number
Record Monitor Serial Number
Record Serial Numbers-Monitor and Control Components
Keep Proof of Ownership
Keep Machines Secure
Section : SERVLIT - John Deere Service Literature
Technical Information
Section : IBC - John Deere Service Keeps You on the Job
John Deere Is At Your Service