OMFH313140

Print

469, 469S, 569, and 569S Round Baler (N.A.)

All information, illustrations and specifications in this manual are based on the latest information available at the time of publication. The right is reserved to make changes at any time without notice.

Foreword

Section 40 - Operating the Baler

Section 45 - Attachments

Pickup Gauge Wheels (Regular Pickup)
Gathering Wheels
Bale Push Bar
COVER-EDGE™ Surface Wrap Unit
Hydraulic Pickup Lift
Variable Core Valve
BaleTrak™ Pro Monitor-Controller
Monitor-Controller Mounting Brackets
Mounting Kit For Open Station 6000 and 7000 Series Tractors
Ten Ball Twine Storage
Belt Lacing Tool
Skiving Tool
Electrical Outlet Socket
Extended Rear-View Mirror
Right-Hand Rear-View Mirror
Slip Clutch Alert System
Crop Deflector Kit
Fire Extinguisher
Wear Liner Kit
Silage Auger Kit
Auxiliary Take-up Roll
Cornstalk Feeding Enhancement Kit
Pickup Filler Plates for Cornstalks
Grease Bank System
Allied Equipment

Section 50 - Lubrication and Maintenance

Lubricating and Maintaining Machine Safely
Grease
Gear Case Oil
Alternative and Synthetic Lubricants
Observe Lubrication Symbols
Perform Lubrication and Maintenance
Fire Prevention
As Required - Belt Pins
As Required - Tension Arm Wear Channels
First 50 Hours
Every 10 Hours
Every 30 Hours
Every 100 Hours
Annually

Section 55 - Troubleshooting

PTO Driveline Difficulties
Main Drive Friction Slip Clutch
Drive Chain Difficulties
Gear Case Difficulties
Hydraulic Function Difficulties
Automatic Twine Wrap
BaleTrak™ Pro Monitor-Controller Difficulties
Slip Clutch Alert
Feed Difficulties
Feed Difficulties With Roller Baffle
Pickup Difficulties
Bale Quality
General Baler Difficulties
Push Bar Difficulties
High-Moisture Kit Difficulties (Silage Baling)
Net Wrap Difficulties
BaleTrak™ Pro Monitor-Controller Error Codes

Section 60 - Service—Baler

Detailed Service Information
Practice Safe Service Procedures
Fire Prevention
Keep Service Area Clean
Service Tires Safely
Rotate Output Shaft By Hand
BaleTrak™ Pro Component Locations
Wire Diagram—BaleTrak™ Pro Monitor-Controller Control System
Wire Harness Diagram—BaleTrak™ Pro Monitor-Controller
Wire Harness Diagram—Baler
Hydraulic System Diagram
Adjust Initial Length of Pickup Drive Belt Idler Spring—Regular Pickup (569)
Adjust Pickup Drive Belt Idler—Regular Pickup (569)
Adjust Pickup Drive Chains
(MegaTooth™ Pickup)
Adjust Pickup Drive Chains
(MegaWide™ Plus Pickup)
Adjust Lower Drive Roll Chain
Adjust Upper Drive Roll Chain
Adjust Upper Drive Roll Chain Guides
Replace Drive Roll Bearings or Left-Hand Sprockets
Install Left-Hand Upper Drive Roll Bearing
Replace Left-Hand Lower Drive Roll Bearing
Replace Right-Hand Lower Drive Roll Bearing
Install Upper Right-Hand Drive Roll Bearing
Remove Compressor Rack
(Regular and MegaTooth™)
Install Compressor Rack
(Regular and MegaTooth™)
Adjust Compressor Rack
(Regular and MegaTooth™)
Adjust Compressor Rod Channel (MegaTooth™ Pickup)
Remove Compressor Rack
(MegaWide™ Plus)
Install Compressor Rack (MegaWide™ Plus)
Adjust Compressor Rods (MegaWide™ Plus)
Remove and Install Roller Baffle
Adjust Roller Baffle Height
Adjust Roller Baffle Float Tension
Balance Roller Baffle
Replace Teeth (Pickup Installed)
Rotate or Replace Upper Drive Roll Chain Idler Bushing
Adjust Main PTO Driveline Slip Clutch
Slip Main PTO Driveline Slip Clutch
Check Pickup Slip Clutch Torque (MegaTooth™ or MegaWide™ Plus)
Adjust PTO and Drive Roll (Pickup) Slip Clutch Alert Sensors
(MegaWide™ Plus and MegaTooth™ Pickups)
Turn On and Off Net Wrap, Slip Clutch Alert, and Variable Core Features
Check Belt Tracking
Adjust Belt Tracking
Adjust Lower Gate Roll Scraper
Adjust Starter Roll Scraper (If Equipped)
Adjust Idler Roll Scrapers (If Equipped)
Adjust Auger Scrapers (MegaWide™ Plus Pickup)
Check and Adjust Clearance Between Cleaning Auger and Staggered Belt Roll (469S and 569S)
(469 and 569 If Equipped)
Adjust Take-Up Arm Compression Springs
Twine Arm Calibration (Channel 029)
Adjust Twine Indicator Retaining Strap
Adjust Twine Guide Arm Spring
Adjust Twine Cutter Tension
Adjust Clearance Between Cutter Link Support and Twine Arm
Adjust Front Twine Arm
Adjust Twine Cutter-to-Twine Arm
Twine Arm Timing (569 and 569S)
Check and Adjust Twine Cutter Knife
Twine Electric Actuator Installation Adjustment
Adjust Twine Arm-to-Starter Roll, Cutter Link Support, and Twine Arm Stop
Adjust Pickup Float Springs
(Regular Pickup) (569)
Adjust Pickup Float Springs
(MegaTooth™ Pickup)
Adjust Pickup Float Springs
(MegaWide™ Plus Pickup)
Check Pickup Tooth Rotational Play
Adjust Gate Latch Stop
Adjust Gate Latch Linkage
Replace Bale Diameter Sensor
Replace Bale Shape Sensor
Replace Gate Latch Proximity Switches
Replace Oversize Bale Switch
Adjust Bale Diameter Sensor (Channel 005)
Adjust Bale Shape Sensor—Field Procedure (Channels 007 and 009)
Adjust Bale Shape Sensor—In Shop Procedure (Channels 007 and 009)
Test Oversize Bale and Gate Latch Switches—Monitor-Controller Assisted Test (Channel 013, 014, and 015)
Test Twine or Net Wrap Actuator Current (Channel 018)
Test Tractor Convenience Outlet Voltage (Channel 019)
Test Liquid Crystal Display (LCD) Panel (Channel 020)
Adjust Oversize Bale Switch
Adjust Gate Latch Proximity Switches
Check Microswitches
Raise Gate With Hoist
Check Belt Pins
Belt Lacing and Pin Installation
Incorrect Belt Lacing and Pin Installation
Install Belts
Repair Belts
Belts Eligible For Warranty Replacement
Belts Not Eligible for Warranty Replacement

Section 61 - Service—Net Wrap

Detailed Service Information
Practice Safe Service Procedures
Net Wrap Use After Extended Storage
Release Net Wrap Feed Roll Brake
Net Wraps on Rubber Drive Roll
Correct Net Wrap Feeding Problems
Check For Looped Net Wrap Material
Check and Adjust Net Wrap Feed Roll Brake
Check Front Sheet-to-Rubber Roll Clearance
Repair Cuts on Rubber Feed Roll
Adjust Net Wrap Counterknife
Sharpen Net Wrap Knife
Install and Adjust Net Wrap Brush
Check and Adjust Net Pan Pressure
Check and Straighten Net Pan Angle
Check and Adjust Net Pan Pressure without Leaf Spring
Check For Bent Rubber Crop Deflectors
Check and Adjust Net Wrap V-Belt Idler Tension
Check For Left-Hand Side Counterknife Contact
Check Hole Wear in Surface Wrap Side Panel
Check and Adjust Net Wrap Feed Roll Brake Spring
Adjust Net Wrap Feed Roll Pressure
Test Net Wrap Switch—Monitor-Controller Assisted Test (Channel 012)
Check and Adjust Net Wrap Switch
Remove and Install Knife
Test Net Wrap Actuator Current (Channel 018)
Remove Net Wrap Actuator
Install Net Wrap Actuator
Remove and Install Net Wrap V-Belt
Check and Adjust Lower Belt Guides
Adjust Net Wrap Stretch

Section 65 - Storage

End of Season
Start of Season

Section 75 - Specifications

469 Round Baler Specifications
469 Silage Special Round Baler Specifications
569 Round Baler Specifications
569 Silage Special Round Baler Specifications
BaleTrak™ Pro Monitor-Controller Specifications
Tractor Compatibility
Hitch Weights
Metric Bolt and Screw Torque Values
Unified Inch Bolt and Screw Torque Values

Section 80 - Serial Numbers

Serial Number Plate
Serial Number Plate Description
Record Baler Serial Number
Keep Proof of Ownership
Keep Machines Secure

Section SERVLIT - John Deere Service Literature Available

Technical Information

Section IBC - John Deere Service Keeps You On The Job

John Deere Is At Your Service

Print

469, 469S, 569, and 569S Round Baler (N.A.)

Section 05 - Safety Features

Section 10 - Safety

Section 15 - Safety Sign Location

Section 16 - In Case of Fire

Section 20 - Preparing the Tractor

Section 25 - Preparing the Baler

Section 26 - Preparing Baler for Net or B-Wrap

Section 30 - Attaching and Detaching

Section 35 - Transporting

Section 36 - Break-In Period