6650, 6750, 6850 and 6950 Self-Propelled Forage Harvesters (504992-      )

All information, illustrations and specifications in this manual are based on the latest information available at the time of publication. The right is reserved to make changes at any time without notice.

Foreword

Section : 00 - Identification Views

Identification Views

Section : 05 - Safety

Recognize Safety Information
Follow Safety Instructions
Understand Signal Words
Observe Road Traffic Regulations
Handle Fuel Safely-Avoid Fires
Prevent Machine Runaway
Use Safety Lights and Devices
Handle Starting Fluid Safely
Prepare for Emergencies
Wear Protective Clothing
Store Attachments Safely
Mount and Dismount Safely
Operate Forage Harvester Safely
Wear Seat-Belt
Keep Riders Off the Machine
Driving the Forage Harvester
Guards and Shields
Stay Clear of Harvesting Units
Keep Hands Away From Knives
Stay Clear of Rotating Drivelines
Avoid Entanglement
Transport With Harvesting Unit Installed
Ballasting for Safe Ground Contact
Avoid Power Lines
Parking and Leaving the Forage Harvester
Work In Ventilated Area
Emergency Exit
Practice Safe Maintenance
Support Machine Properly
Retorque Wheel Nuts
Avoid High-Pressure Fluids
Service Cooling System Safely
Dispose of Waste Properly

Section : 10 - Safety Decals

Link

Section : 15 - Controls and Instruments

General View of Controls and Instruments
Switch Console
Multi-Function Lever
Corner Post
Roof Switch Console
Roof Console
Automatic Function Control
Steering Column
Main Clutch Switch
Rocker Switch for Raising/Lowering Discharge Spout
Metal Detector Tumbler Switch
Rocker Switch for Metal Detector Test
Harvesting Unit Float Rocker Switch
Trailer Dump Rocker Switch (Option)
Spout Rinsing Tumbler Switch
Harvesting Unit/Reverser Rocker/Tumbler Switch
Rotary Switch for Header Height Resume Control
Adjusting Header Ground Pressure Gauge
Foot-Operated Switch - Two Speed Spout Rotation
Engine Speed Control Knob
Gear Shift Lever
Fan Switch
Cooling Compartment Switch (With Air Conditioning Only)
Air Conditioning/Heater Switch
Rocker Switch for Rotary Header/Windrow Deflector (Options)
Demoisturizer Tumbler Switch (With Air Conditioning System Only)
Quick Stop Switch On Multi-Function Lever
Rocker Switch - Discharge Spout Cap Adjustment
Rocker Switch - Raise/Lower Harvesting Unit
Rocker Switch - Turn Discharge Spout
Switching ROW-TRAK™ On/Off
Service Code Switch (6950 Only)
Windshield Wiper Tumbler/Rocker Switch
Windshield Washer Rocker Switch
Side Window Wiper/Washer Tumbler/Rocker Switch (Option)
Horn Button
Ether Starting Aid Button
Starter Switch

Section : 20 - Warning Devices and Monitors

Indicator Lights I
Engine Oil Pressure Indicator Light
Coolant Temperature and Charge Air Temperature Indicator Light
Parking Brake Indicator Light
Brake Fluid Indicator Light
Hydrostatic Oil Temperature Indicator Light
Hydraulic Oil Temperature Indicator Light
Metal Detector Indicator Light
Rotary Suction Screen Indicator Light
Coolant Level Indicator Light
Engine Stop Light (6950 Only)
Engine Warning Light (6950 Only)
Engine Protection Light (6950 Only)
Indicator Lights II
Fuel Level Indicator Light
Air Cleaner Indicator Light
Indicator Light for Alternator 1
Hydraulic Oil Filter Pressure Indicator Light
Hydrostatic Charge Pressure Indicator Light
Indicator Light for Alternator 2
Intercooler Indicator Light
Cutterhead Speed Indicator Light
Spout Rinsing Pump Indicator Light
Four Wheel Drive Indicator Light
Air Conditioner Indicator Light (High Pressure)
Fuel Gauge
Coolant Temperature Gauge
Header Height Gauge
Ground Pressure Gauge
Control Lights of Automatic Function Control
INFO-TRAK™ Monitor
INFO-TRAK™ Monitor Functions
Setting and Displaying Time
Input of Specific Machine Data
Software Version
Machine Code
Transmission Speed Ratio Code
Tire Radius Code
Determining Tire Radius
Engine Impulse Code
Setting Cutterhead Alarm Speed
INFO-TRAK™ Monitor Service Information
Adjusting Unit for Kernel Processor Rolls, Stationary Knife and Knife Sharpening
Adjusting Sharpening Cycles On INFO-TRAK™ Monitor
Activating Automatic Knife Sharpening
Moving Sharpening Stone Manually
Adjusting The Automatic Knife Sharpening Device
Automatic Stationary Knife Adjustment
Increasing Stationary Knife-to-Knife Clearance (Manual Adjustment)
Adjusting Kernel Processor Roll Clearance On INFO-TRAK™ Monitor
Activating Automatic Adjustment of Kernel Processor Roll Clearance
Increasing Kernel Processor Roll Clearance (Manual Adjustment)
Control Unit for ROW-TRAK™
Putting ROW-TRAK™ into Operation
Correcting the ROW-TRAK™
Taking ROW-TRAK™ Out of Operation
Selecting the Calibration Mode
System Gain
Steering Ratio
Row Feeler Filtering
Changing the Header
Calibrating the Feelers on the Header - General Information
Calibrating the Left-Hand Feeler On Row-Dependent Header
Calibrating the Right-Hand Feeler On Row-Dependent Header
Calibrating the Right-Hand Feeler On Row-Independent Header
Calibrating the Left-Hand Feeler On Row-Independent Header
Area Counter (Option)
Display
Area Counter
Control Keys
Selecting Area Counter Functions
Clearing "Area Per Day" or "Total Area Per Day"
Changing Header Width
Setting Partial Header Width
Displaying Cutterhead Operating Hours
Clearing Cutterhead Operating Hours
Displaying Travel Distance
Clearing Travel Distance

Section : 25 - Lighting System and Signals

Parking Light and Low-Beam Tumbler Switch
Full-Beam Tumbler Switch
Full-Beam Indicator Light
Headlights
Tumbler Switch, Low-Beam Headlights On/Off for Row-Independent (Rotary) Header
Headlights (Special Equipment for Rotary Harvesting Unit)
Turn Signal Switch
Turn Signal Indicator Light
Turn Signal Indicator Light for Trailer
Turn Signal and Clearance Lights - Front
Rear Turn-Signal Lights, Tail Lights and Stop Lights
Work Light Tumbler Switch
Work Lights
Tumbler Switch for Hazard Warning Lights
Using Hazard Warning Lights
Indicator Light Test Rocker Switch

Section : 30 - Operator's Cab

Opening Cab Door
Adjusting Operator's Seat Position
Adapting Seat to Operator's Weight
Adjusting Lumbar Support
Operator's Seat Safety Switch With Alarm
Seat-Belt
Adjusting L.H. Armrest
R.H. Armrest - Fore-and-Aft Adjustment
Ashtray
R.H. Armrest Storage Compartment
Cover of R.H. Armrest
Air Comfort Seat
Passenger Seat
Storage Compartment for Operator's Manuals
Auxiliary Power Outlet
Cooling Compartment
Steering Wheel Height Adjustment
Steering Column Tilt Adjustment
Foot Brakes
Parking Brake
Releasing Parking Brake
Cab Side Window
Remote Control for Semi-Automatic Hitch
Sun Visor
Inside Mirror
Outside Mirror
Interior Lighting
Adjustable Air Louvers
Radio and Citizen Band (Special Equipment)
Fire Extinguisher

Section : 35 - Pre-Starting Checks

Daily Checks
Engine Oil Level
Hydraulic Oil Level
In Winter
Fuel Level
After Long Storage Period
Tires
Fuel System
Lubricate Forage Harvester
Checks in Operator's Cab

Section : 40 - Operating the Engine

Breaking in the Engine
Safety Rules for Starting Engine
Before Starting the Engine
Turn On the Power for the Electronics
Turn On Ignition
Starting the Engine
Engine Oil Pressure Indicator Light
Warming Up Engine
Idling the Engine
Cold Weather Starting Aids
Cold Weather Starting Procedure With Ether Starting Aid
Instructions for Using Cold Weather Starting Aid
Changing Starting Fluid Cans
Electric Coolant Heater
Starting the Engine by Means of a Booster Battery
Operating in Tropical Conditions
Stopping the Engine
Stalling of Engine
Cold Weather Operation

Section : 45 - Driving and Transporting Forage Harvester

Wear Seat-Belt
Starting the Engine
Steering and Driving
Releasing Parking Brake
Operating Foot Brakes
Engaging a Gear
Adjusting Engine Speed
Raising Harvesting Unit
Forward and Reverse Travel
Choosing Correct Travel Speed
Avoid Overheating of Hydrostatic System
Four Wheel Drive
Transport Information
Hitch
Transport Hooks
Slotted Holes for Securing Forage Harvester During Transport
Transporting the Forage Harvester on the Truck

Section : 50 - Wheels and Ballast

Tire Maintenance
Tubeless Tires
Wheel Bolts and Nuts
Mounting Tires
Changing Tires
Tires
Tire Pressures
Rear Weights for Forage Harvester With Harvesting Unit Installed
Number of Suitcase Weights/Weight Plates with Standard Rear Axle
Number of Suitcase Weights/Weight Plates with Powered Rear Axle
Number of Suitcase Weights When a Weight Carrier is Used
Overall Width and Track Width
Track Width of Front Wheels
Total Widths and Tread Widths with Adjustable Rear Axle
Rim Chart
Axle Spacer Attaching Screws

Section : 55 - Harvesting Units and Attachments

2.14 M (7 Ft) and 3 M (10 Ft) Pickups
4.50 Meter Pickup Unit
Attaching Frame for 2.14 M (7 Ft) Pickup
3-Row Row-Crop Unit
Attaching Frame for 3-Row Row Crop
Adapter Frame for 2.14 M (7 Ft) Pickup and 3-Row Row Crop
4-Row Row-Crop Unit
5-Row and 6-Row Row-Crop Units
676 Rotary Harvesting Unit (Row-Independent)
688 Rotary Harvesting Unit (Row-Independent)
710 Rotary Harvesting Unit (Row-Independent)
Corn Heads
Corn Head Cross Drive
Kernel Processor
Kernel Processor Rolls for Sorghum
Electrical Adjustment of Kernel Processor Roll Spacing
Power Chute
Recirculating Screens
Recutter Floor
Grass Channel (Stainless Steel)
Fan Speed
Power Rear Wheel Drive
Wheel Spacer
Hydraulic Outlet
Cold Weather Starting Aids
Side Window Wiper
Second Spout Work Light
Spout Extension
Two-Speed Rotation of Discharge Spout (Field Kit)
Extra Fuel Tank (Field Kit)
Muffler Extension
Semi-Automatic Hitch
Weight Carrier
Intake Screen with Wider Mesh

Section : 60 - Attaching and Detaching Harvesting Units

Attaching Sequence - 6-Row Row Crop
Connecting Harvesting Unit Drive Shaft

Section : 65 - Preparations and Field Operation

Obtaining Optimum Harvesting Performance
Preparations for Harvesting Grass
Preparations for Harvesting Corn
Preparations for Harvesting Ear Corn Silage
Preparations for Harvesting Alfalfa
Preparations for Harvesting Sorghum (Milo)
Attaching Points for Harvesting Unit Lift Cylinders
Adjusting Area Counter Switch
Changing Header
Field Operation of Forage Harvester
Reversing During Operation

Section : 70 - Feeding System

Link
Securing Harvesting Unit Lift Cylinders
Function of the Electromagnetic Clutch
Electromagnetic Clutch Operating Positions
Cutterhead Speed Sending Unit
Length-of-Cut Transmission
Adjusting Length-of-Cut
Adjusting Harvesting Unit Speed
Harvesting Unit Drive Shaft
Feed Roll Slip Clutch
Service of Length-of-Cut Transmission
Length-of-Cut Transmission Oil Change
Feed Roll Drive
Replacing Wear Plates and Stops
Lateral Guides for Upper Feed Rolls
Feed Roll Spring Attaching Points
Adjusting Feed Roll Springs
Opening Feed Roll Housing
Adjusting Smooth Roll Scraper
Cover Plates Under Feed Rolls
Closing Feed Roll Housing
Feed Roll Housing Safety Switch
Hydraulic Reverser Motor
Troubleshooting - Feeding System

Section : 75 - Metal Detector

Metal Detector Operation
IRON-GARD™ Metal Detector
Activating Metal Detector
Operating Forage Harvester With Metal Detector Locked Out
When Ferrous Metal is Detected
Adjusting Locking Pawl
Checking Adjustment
Metal Detector Test
Safety Rules
Relay and Electronic Box
Electronic Box IRON-GARD™ II
Relay Box IRON-GARD™ II
Indicator Light Test Chart
Test Chart 1
Test Chart 2
Test Chart 3
Metal Detector Troubleshooting

Section : 80 - Cutterhead, Drives, Guards, Covers

Cutterhead-Safety Information
Engine Access, Left-Hand Side
Engine Access, Right-Hand Side
Access to Cooling Elements and Main Clutch
Access to Main Drive and Sharpening Device
Cutterhead Drive
Main Clutch
Check Main Clutch
Replacing Main Drive Belt
Checking Belt Alignment
Cleaning Cutterhead
Cutterhead Knives
Number and Arrangement of Cutterhead Knives
Replacing and Adjusting Partial Set of Cutterhead Knives
Replacing Complete Set of Cutterhead Knives
Replacing Clamp Bar
Replacing Threaded Bar
Removing/Sliding Back Cutterhead Knife
Knife Screw Torque
Preparations for Knife Sharpening Procedure
Automatic Knife Sharpening Procedure
Manual Sharpening of Cutterhead Knives
Automatic Knife Sharpening Device
Replacing Sharpening Stone
Aligning Knife Sharpening Device
Retensioning Guide Cable
Stationary Knife
Information for Adjusting Stationary Knife
Manual Stationary Knife Adjustment
Adjusting Stationary Knife
Checking Stationary Knife Adjustment
Checking Stationary Knife for Wear
Removing Stationary Knife
Removing Stationary Knife Adjusting Device
Installing Stationary Knife
Torque at Stationary Knife Adjusting Devices
Eliminating End Play of Adjusting Spindle
Cutterhead Bottom and Outlet Bands
Adjusting Bottom Band
Adjusting Outlet Band
Recirculating Screens
Installing/Changing Recirculating Screen
Adjusting Recirculating Screen
Removing Bottom and Outlet Bands
Installing Spiral Floor
Adjusting the Recutter Floor
Adjusting Spiral Floor
Spiral Floor Adjustment Chart
Adjust the Service Cover on the Transition Chute
Transition Chute Between Cutterhead and Blower Fan
Cutterhead Service Cover
Removing Cutterhead With Harvesting Unit
Installing Cutterhead With Harvesting Unit
Main Drive Troubleshooting
Cutterhead Troubleshooting
Knife Sharpener Troubleshooting
Troubleshooting - Stationary Knife Adjustment

Section : 85 - Kernel Processor

Kernel Processor Quick Conversion
Removing Grass Transition Chute
Tensioning Roller of Kernel Processor Drive Unit
Moving Kernel Processor into Working Position
Engaging Kernel Processor Feed Plate
Engaging Lock
Service Cover and Locking Device
Adjust the Service Cover On the Kernel Processor
Completing Conversion
Changing From Kernel Processor to Grass Transition Chute
Locking Clamp - Kernel Processor Main Drive
Install/Remove the Kernel Processor
Breaking-In Kernel Processor
Field Operation
Kernel Processor Service
Adjusting Roll Spacing
Stop Screws for Roll Clearance Adjustment
Adjusting Clearance Indicator
Pretension of Lower Roll Drive Belt
Adjusting Scrapers
Roll Wear and Replacement
Potentiometer for Automatic Roll Clearance Adjustment
Replacing Drive Belts of Lower Roll
Troubleshooting

Section : 86 - Power Chute

Power Chute-Safety Information
Possible Power Chute Installations
Installing the Power Chute on the Kernel Processor
Installing the Power Chute on the Attaching Frame
Power Chute - Service and Operation
Drive Belts

Section : 90 - Discharge

Blower and Discharge Spout - General Information
Blower Bottom With Wear Plate
Replacing Wear Plate
Installing Wear Plate
Torques for Hardware
Adjusting Blower Paddles
Adjusting Deflecting Edges
Service Opening and Wear Plates at Spout
Intake Opening of Blower Fan
Spout Worm Gear and Ring Gear

Section : 95 - Fuel, Lubricants, Coolant and Capacities

Diesel Fuel
Handling and Storing Diesel Fuel
Lubricity of Diesel Fuel
Filling the Fuel Tank
Fill Extra Fuel Tank
Engine Break-In Oil
Diesel Engine Oil
Engine Crankcase Capacity Including Filter Change
Diesel Engine Coolant
Liquid Coolant Conditioner
Cooling System Capacity
Transmission Oil
Use of Transmission Oil
Transmission and Hydraulic Oil
Use of Transmission and Hydraulic Oil
Brake Fluid for Brake System
Grease
Alternative and Synthetic Lubricants
Mixing of Lubricants
Lubricant Storage
Use Genuine John Deere Parts

Section : 100 - Lubrication, Periodic Service

Important Lubrication Instructions
Greasing Points Not Lubricated Centrally
Central Lubrication System (Option)
Operational Information
Adjusting Pump Element (A) for Flow Control
Quick Couplers for Kernel Processor and Harvesting Unit
Location of Primary and Secondary Distributors
Troubleshooting - Central Lubrication System
Break-In Service
Observe Service Intervals
Every 10 Operating Hours
After the First 100 Operating Hours:
Every 250 Operating Hours:
Every 500 Operating Hours
Every 1000 Operating Hours
Every 1500 Operating Hours:
Every 2000 Operating Hours
As Required:
Every Year
Every 2 Years
V-Belts
Chains

Section : 105 - Service - Engine

Engine Compartment
Adjusting Engine Valve Tappet Clearance
Rocker Arm Cover and Crankcase Ventilation - Cummins Engine
Rocker Arm Cover Ventilation
Checking Engine Crankcase Oil Level
Changing Engine Oil and Filter, John Deere POWERTECH® 8.1 L Engine
Changing Engine Oil and Filter, John Deere POWERTECH® 12.5 L Engine
Changing Engine Oil and Filter (Cummins Engine)
Link
Do Not Modify Fuel System
Fuel Filler Neck
Fuel Tank Water Trap
Fuel System - John Deere POWERTECH®8.1L Engine
Fuel System - John Deere POWERTECH®12.5 L Engine
Fuel System - Cummins Engine
Fuel Shut-Off Valve
Water Trap
Draining Water From Fuel Filter
Replacing the Fuel Filter Element, John Deere POWERTECH® 8.1 L Engine
Replacing the Fuel Filter Element, John Deere POWERTECH® 12.5 L Engine
Checking Fuel Injection Nozzles - John Deere POWERTECH® Engine
Bleeding Fuel System - John Deere POWERTECH® Engine
Fuel Filter With Integrated Water Trap - Cummins Engine
Cleaning Rotary Radiator Screen
Access to Cooling Elements
Cleaning Cooling Elements
Cooling Element Location (6650, 6750 and 6850)
Cooling Element Location (6950)
Rotary Radiator Screen - Winter Operation
Flushing Sequence - Cooling System
Engine Coolant
Engine Coolant Drain Taps (6650)
Engine Coolant Drain Taps and Plugs (6750, 6850)
Engine Coolant Drain Taps (6950)
Adding Coolant
Heater Shut-Off Valve
Replacing Coolant Conditioner (6950)
Checking Belt Tensioner Spring Tension and Belt Wear (John Deere Engines)
Tensioning Alternator Drive Belt - Cummins Engine
Tensioning Fan Drive Belt - Cummins Engine
Tensioning Water Pump Drive Belt - Cummins Engine
Air Intake Prefilter Screen
Removing Air Cleaner Primary Element
Removing Safety (Secondary) Element
Air Cleaner (Primary) Element and Safety (Secondary) Element
Cleaning Air Cleaner Housing
Cleaning Air Cleaner Primary Element
Inspecting Element
Element Storage
Installing Air Cleaner Element
Air Intake Lines
Turbocharger - John Deere Engine
Turbocharger - Cummins Engine
Checking Crankshaft Vibration Damper (John Deere Engines)
Checking Crankshaft Vibration Damper (Cummins Engine)

Section : 110 - Service - Electrical System

Electrical System - Specifications
Batteries (6650, 6750 and 6850)
Batteries (6950)
Dangers When Handling Batteries
Battery Service
Checking Electrolyte Level
Checking Specific Gravity
Installing and Connecting Batteries
Alternators
Starter Motor
Access to Fuse Board
Fuse Tester and Spare Fuses On Fuse Board
Access to Circuit Boards
Removing a Circuit Board
Access to Electronic Control Unit
Access to Relay and Diode Board
Sockets
Trailer Socket
Socket for Header Lighting
Socket for Header Electrical System (Option)
Storage Module
Electronic System Boards
Fuse Board - Fuses
Extra Fuses for Cummins ECU
Fuse Board - Relays
Shift Relays (6750 and 6850 Only)
Relay and Diode Board
Solenoids - Left-Hand Side
Solenoids - Right-Hand Side
Electronic Control Unit (ECU)
Sending Units for Electronic Control Unit (ECU) (6750, 6850)
Sending Units for Electronic Control Unit (ECU) (6950)
Service Codes, Automatic Function Control - General
Service Codes, Automatic Function Control
Service Codes for Electronic Control Unit (ECU) (8.1 L Engine) - General
Service Codes - John Deere Engine Control Unit for 6081 POWERTECH® Engine
Service Codes - John Deere Engine Control Unit for 6125 POWERTECH® Engine
Self-Test of Engine Electronic System (6950 Only)
Service Codes, Cummins Engine
Work Lights On Cab Roof
Rear Work Lights
Clearance and Turn Signal Lights, Front
Tail, Stop and Turn Signal Lights, Rear
Dome Light
Switch Lighting
Indicator Light Bulbs
Access Ladder and Registration Plate Lighting

Section : 115 - Service - Hydraulic System

Avoid High-Pressure Fluids
Pressure Relief Valve
System Description
Accumulators
Accumulator - Discharge Spout
Draining Hydraulic Oil
Replacing Hydraulic Oil Filter
Refilling Hydraulic Oil
Temperature and Pressure Sending Units at Hydraulic Oil Tank

Section : 120 - Service - Ground Speed Drive

Brake System
Brake Fluid Reservoir
Adjusting Foot Brakes
Parking Brake
Hydrostatic Drive Oil Cooler
Hydrostatic Drive - Filter Change
Hydrostatic Drive - Adjusting Cable
Transmission
Final Drives
Final Drive Attaching Screws
Transmission Attaching Screws to Front Axle
Front Axle
Rear Axle Toe-In
Steering Cylinder Support Attaching Screws to Rear Axle
Steering Cylinder Support Attaching Screws to Wheel Motor
Wheel Motor Yoke Attaching Screws to Rear Axle Sliding Sleeve
Adjusting Rear Axle Width

Section : 125 - Service - Air Conditioning System, Heater

Air Conditioning System Components
Heater Components
Compressor Drive Belt
Checking Refrigerant Level
Low Pressure Switch
High Pressure Switch
Cleaning Condenser
Cab Filters
Removing Paper (Main) Filter Element
Cleaning Paper Filter Elements
Removing Recirculating Filter
Air Intake Opening
Condensed Water Drain Hose

Section : 130 - Storage

After the Season
After the Season - Engine
After the Season - Air Conditioning System
Removing Forage Harvester From Storage
Removing Forage Harvester From Storage - Engine
Removing Forage Harvester From Storage - Air Conditioning System

Section : 135 - Specifications

6650 Forage Harvester
6750 Forage Harvester
6850 Forage Harvester
6950 Forage Harvester
6650, 6750, 6850 and 6950 Forage Harvesters
Dimensions
Metric Bolt and Cap Screw Torque Values
Unified Inch Bolt and Cap Screw Torque Values
Limited Battery Warranty
Emissions Control System Certification Label
U.S. Emissions Control Warranty Statement
California Emission Control Warranty Statement (California Only)

Section : 140 - Serial Numbers

Serial Number Plates
Forage Harvester (Product Identification) Type Plate
Product Identification Number
Engine Serial Number - Cummins Engine
Engine Serial Number - Engine Type 6081
Engine Serial Number - Engine Type 6125
Operator's Cab Serial Number
Four Wheel Drive Motor Serial Number
Kernel Processor Serial Number
Power Chute Serial Number
Three-Speed Transmission Serial Number
Final Drive Serial Number
Angled Drive (Main Gearcase) Serial Number
Length-of-Cut Transmission Serial Number
Hydrostatic Pump Serial Number
Hydrostatic Motor Serial Number

Section : 145 - Crime Prevention Tips

Help Prevent Crime
Record Ag Identification Numbers
Keep Proof of Ownership
Park Indoors Out of Sight
When Parking Outdoors
Reduce Vandalism
Report Thefts Immediately

Section : SLIT - John Deere Service Literature Available

Technical Information

Section : IBC - John Deere Service Keeps You On The Job

John Deere Is At Your Service When You Need It