S660, S670, S680
and S690 Combines
(S.N. 755001— )
Copyright 2012 © Deere & Company. THIS DATA IS THE PROPERTY OF DEERE & COMPANY. ALL USE AND/OR REPRODUCTION NOT SPECIFICALLY AUTHORIZED BY DEERE & COMPANY IS PROHIBITED.
All information, illustrations and specifications in this manual are based on the latest information available at the time of publication. The right is reserved to make changes at any time without notice.
Foreword
Machine Photo
Section 05 - Safety Features
Machine Safety Features
Section 10 - Safety
Recognize Safety Information
Understand Signal Words
Follow Safety Instructions
Spanish Safety Signs and Operator's Manual
Replace Safety Signs
Driving the Machine
Keep Riders and Children Off Machine
Ballasting for Safe Ground Contact
Avoid Electrical Power Lines
Parking and Leaving the Machine
Work In Ventilated Area
Handle Fuel Safely—Avoid Fires
In Case of Fire
Prepare for Emergencies
Handle Starting Fluid Safely
Wear Protective Clothing
Stay Clear of Harvesting Units
Keep Hands Away From Knives
Use Safety Lights and Devices
Use Seat Belts
Transport Combine With Header Safely
Prevent Machine Runaway or Unexpected Movement
Practice Safe Maintenance
Welding Near Electronic Control Units
Remove Paint Before Welding or Heating
Avoid Heating Near Pressurized Fluid Lines
Avoid Contact With Moving Parts
Cleaning Grain Tank and Removal of Blockages Safely
Stay Clear of Rotating Drivelines
Install All Shields and Guards
Avoid High-Pressure Fluids
Do Not Open High-Pressure Fuel System
Service Accumulator Systems Safely
Protect Against High Pressure Spray
Service Tires Safely
Dispose of Waste Properly
Service Cooling System Safely
Remove Accumulated Crop Debris
Support Machine Properly
Store Attachments Safely
Service Drive Belts Safely
Handle Electronic Components and Brackets Safely
Avoid Backover Accidents
Handling Batteries Safely
Clean Exhaust Filter Safely
Avoid Hot Exhaust
Exhaust Filter Cleaning
Section 15 - Safety Sign Location
Front View Decals
Feeder House Left-Hand Decals
Cab Decals and Ladder Decals
Left-Hand View Decals
Left-Hand View Residue Decals
Rear View Decals and Engine View Decals
Right-Hand View Residue Decals
Right-Hand View Decals
Feeder House Right-Hand View Decals
Top View Decals
Section 20 - Controls and Instruments
General View of Controls and Instruments
Section 25 - Overhead Control Panel
Overhead Control Panel
Microphone (Optional)
Mirror Heater Switch (Optional)
Mirror Control Switch (Optional)
Radio Types (Optional)
After Market Radios
Program Radio for Local Area Frequency
Radio Controls
Antenna
Communications/CB Radio Mounting
Section 30 - CommandCenter Display Screens
Armrest Display Navigation (GreenStar™ 3 CommandCenter™ Non-Touchscreen)
Armrest Display Navigation (GreenStar™ 3 CommandCenter™ Touchscreen)
Armrest Display Navigation (GreenStar™ 3 2630 Display)
Display Navigation Layouts
Display Icon Identification
Display Region Layouts
Display Left Region Layouts
Combine—Main Screen
Manual Recording ON/OFF
Reconfigure Detail Machine Settings
Reconfigure Performance Monitor Settings
Harvesting Information Screen
Select Yield Wet or Dry and Cut Width Change
Clear Field Totals
Clear Crop Totals
Combine Setup Screen
Change Machine Settings
Change Crops and Seed Sensitivity Size
Change Moisture Settings and Yield Units Settings
Yield Calibration
Single Point Yield Calibration Or Multi-Point Yield Calibration
Change Tire Radius Code
Moisture Sensor Temperature Calibration
Payable Moisture and Density Chart
Standard Weights Chart
Harvest Smart Feed Rate (If Equipped)
Grain Tank Level and Unloading Rate Offset Setup
Folding Functions Setup
Residue Management Setup
Header Setup Screen
Change Header Settings
Automatic Header Control (AHC) Settings
Engine Information Screen
Exhaust Filter Cleaning (Interim Tier 4/Stage III B)
Diagnostic and Calibrations Screen
Radio Source Select
AM/FM/WX Home Page
XM® Radio
Services Home Page (Premium Radio) (United States/Canada Only)
CD/MP3 Home Page
USB Home Page (Premium Radio)
Auxilary (AUX) Home Page
Bluetooth® Audio
Radio Settings
Operating the Phone (Premium Radio)
Phone Book (Premium Radio)
Phone Directories (Premium Radio)
Phone Settings (Premium Radio)
Signal Strength and Battery Indicator (Premium Radio)
Brightness Level and Boundary Box Color
Regional Settings, Languages, Time/Date Settings, Units of Measurement
Diagnostic Readings, About, Display Tests
Connecting Multiple Displays and Auxiliary Controls
Message Center Application
Performance Monitor Application
Layout Manager Application
Video Interface Capability
Video Application (If Equipped)
Access Manager Application
Section 35 - CommandTouch Armrest Console
Armrest Console Controls
Header Engage and Feeder House Reverser Switch
Shifting Feeder House Reverser
Separator Engage Switch
Harvest Smart Feed Rate Enable Switch (If Equipped)
Engine Speed Switches
Push Button Shift Gear Switches (If Equipped)
ProDrive Mode 1 and 2 Switches (ProDrive Machines) (If Equipped)
Park Brake Switch (If Equipped)
Four-Wheel Drive Switches (If Equipped)
Differential Lock Switch (If Equipped)
Header Height/HydraFlex™ Pressure Control Dial
Dial-A-Speed Dial
Road Transport Disconnect Switch
Folding Functions Shortcut Switch (If Equipped)
CommandARM™ Controls
Header Adjust Switch
Threshing Speed Adjust Switch
Cleaning Fan Speed Adjust Switch
Spreader Speed Adjust Switch
Discharge Swap Switch (If Equipped)
Feeder House Rate/Sensitivity Adjust Switch
Threshing Clearance Adjust Switch
Chaffer/Sieve Adjust Switch
Chopper Vane Angle Adjust Switch (If Equipped)
Operator Interface Controls
Setpoint Modes (Manual or Automatic)
ClimaTrak™ Automatic Temperature Control
Light Switches
Radio Function Switches (If Equipped)
Multi-Function Lever
Multi-Function Lever and Palm Adjustment
Quick Stop Switch
Unloading Auger Swing Switch
Unloading Auger Drive Switch
Header Raise/Lower Switch
Lateral Tilt Switch
Platform Reel Lift/Reel Fore and Aft Switch
Corn Head Backshaft Speed/Adjustable Deck Plate Spacing Switch
Header Activation Buttons
AutoTrac™ Resume Button (If Equipped)
Section 40 - CommandTouch Cab Cornerpost
CommandTouch Cab Cornerpost
Active Header Control Display
Description of Automatic Header Height Control System
Activation Button Mode Combinations
Header Height Resume
Header Height Sensing
Header Height Sensing (HydraFlex Platforms)
Dial-A-Speed System
Lateral Tilt System (Optional)
Active Header Float
Reel Position Resume
Deck Plate Position Resume
VisionTrak Display
VisionTrak Performance Monitor (General Information)
VisionTrak Performance Monitor— Operating
VisionTrak—Preliminary Adjustments on Machine
VisionTrak Operational Checks
Section 45 - Calibration Procedures
Calibration Procedures - When to Calibrate
Calibration Procedures
Calibration Error Codes
Section 50 - Operator’s Station
Manual Storage Location
Emergency Exit
ComfortCommand Operator's Seat (Basic Seat)—Adjusting
ComfortCommand Operator's Seat (Premium Seat)—Adjusting
Left-Hand Armrest and Seat Back (Basic Seat)—Adjusting
Left-Hand Armrest and Seat Back (Premium Seat)—Adjusting
Heated Seat Switch (Optional) (Premium Seat)
Instructional Seat—Adjusting
Refrigerator (If Equipped)
Seat Belts
Armrest Control Console—Adjusting
Armrest Display—Adjusting
Auxiliary Power Outlet Strip
Cab Ladder Positions (Single Tire Configuration)
Cab Ladder Positions (Dual Tire Configuration)
Fire Extinguisher
Fire Extinguisher Locations
Steering Column
Windshield Wiper/Windshield Washer Switch
Gearshift Lever (If Equipped)
Manual Parking Brake (IF Equipped)
Brake Pedals
Handrails and Right-Hand Landing Access
GreenStar™ Display and Harvest Monitor/Harvest Doc™ Systems
Section 55 - Lights and Signals
Light Switches
Lighting Locations
Lighting Delay/Timeout
Turn Signals
Cab Interior Light
Map Light
Section 60 - Feeder House
Hydraulic Cylinder Safety Stop
Feeder House Side Shields
Feeder House Doors
Feed Accelerator Top Access Door
Feeder House Bottom Door and Feedplate Seal Support
Stone Trap
Feeder House Fore/Aft Tilt Frame—Adjusting
Feeder House Conveyor Chain—Adjusting
Feeder House Conveyor Chain Links—Removing
Feeder House Drum—Height Adjustment
Feeder House Conveyor Speed—Changing
Feeder House Conveyor Drive Chain—Adjusting
Feeder House Top Shaft Stripper—Adjusting
Feeder House Top Shaft Sprockets
Feeder House Variable Speed Drive Belt—Replacing
Feeder House Variable Speed Drive Belt—Adjusting
Header Reel/Belt Pickup Pump Belt (Variable Speed Feeder House)—Replacing
Header Reel/Belt Pickup Pump Belt (Variable Speed Feeder House)—Adjusting
Feeder House Fixed Speed Drive Belt—Replacing
Feeder House Fixed Speed Drive Belt—Adjusting
Header Reel/Belt Pickup Pump Belt (Fixed Speed Feeder House)—Replacing
Header Reel/Belt Pickup Pump Belt (Fixed Speed Feeder House)—Adjusting
CommandTouch Multi-Speed Feeder House Drive Belt—Replacing
CommandTouch Multi-Speed Feeder House Drive Belt—Adjusting
Header Reel/Belt Pickup Pump Belt (CommandTouch Multi-Speed
Feeder House)—Replacing
Header Reel/Belt Pickup Pump Belt (CommandTouch Multi-Speed
Feeder House)—Adjusting
Manual Tilt Indicator (Lateral Tilt System)
Attach Multi-Coupler and Single Point Latching
Attaching and Detaching Header from Feeder House
Single Point Latching—Adjusting
Level Land Feeder House Lower Cable End—Adjusting
Level Land Feeder House—Shim Adjusting
Feeder House Latching Pins (Cleanout)
Feeder House Manual Unlatching
Shear Screw Location
Section 65 - Shields
Gull Wing Doors
Left-Hand Side Shields
Right-Hand Side Shields
Separator Covers
Section 70 - Separator
Standard Feed Accelerator—Wing Replacing
Tough Crop Feed Accelerator—Wing Replacing
Tine Feed Accelerator—Wing Replacing
Tine Feed Accelerator Comb Floor (Rice Machines)
Feed Accelerator Belt—Replacing
Feed Accelerator Belt—Adjusting
Standard Speed High Capacity Feed Accelerator—Changing
Speed
High Speed High Capacity Feed Accelerator—Changing To
Slow Speed
Concave Types
Separator Grate Spacers
Concave Sector Gear Shear Bolts
Concave Sections—Remove and Install
Concave Leveling
Separator Top Cover Vanes (If Equipped)
Threshing Elements and Tines (TriStream Rotor)—Remove
and Install
Threshing Element and Separator Tine Location (TriStream Rotor
Standard Configuration) (S660 and S670)
Threshing Element and Separator Tine Location (TriStream Rotor
Tough Grain Configuration)
Threshing Element and Separator Tine Location (TriStream Rotor
Dense Pack Configuration)
Threshing Elements and Tines (Variable Stream Rotor)—Remove
and Install
Threshing Element and Separator Tine Location (Variable Stream
Rotor Standard Configuration)
Threshing Element and Separator Tine Location (Variable Stream
Rotor Dense Pack Configuration)
Posi-Torq™ Separator—Dual-Range
Separator Drive Sheave Gap—Adjusting
Separator Variable Drive Belt—Replacing
Auger Bed Dividers
Discharge Beater Belt—Adjusting
Discharge Beater Belt—Replacing
Discharge Beater—Wing Replacing (S660 and S670)
Standard Discharge Beater—Wing Replacing (S680 and S690)
Tough Crop (Rice) Discharge Beater—Wing Replacing
Overshot Beater Belt (If Equipped)—Adjusting (S670, S680
and S690)
Overshot Beater Belt (If Equipped)—Replacing (S670, S680
and S690)
Overshot Beater (If Equipped)—Wing Replacing (S670, S680
and S690)
Countershaft Right-Hand Front Belt—Adjusting
Countershaft Right-Hand Front Belt—Replacing
Countershaft Right-Hand Rear Belt—Adjusting
Countershaft Right-Hand Rear Belt—Replacing
Cleaning Shoe Air Chutes
Cleaning Shoe Access Door (Spreader Machines)
Cleaning Shoe Auger Gears—Manual Cleanout Door (If Equipped)
Cleaning Shoe Auger Gears—Cleanout Door (If Equipped)
Shoe, Fan and Conveyor Auger Belt—Adjusting
Shoe, Fan and Conveyor Auger Belt—Replacing
Cleaning Fan Belt—Replacing
Cleaning Fan Actuator—Adjusting
Deep-Tooth Front Chaffer
Chaffer and Sieve—Measuring
General Purpose Chaffer 29 mm (1-1/8 in.)
Deep-Tooth Chaffer 41 mm (1-5/8 in.)
General Purpose Sieve 29 mm (1-1/8 in.)
Deep-Tooth Sieve 29 mm (1-1/8 in.)
Chaffer/Sieve Adjusting Switch
Chaffer/Sieve Elements—Remove and Install
Chaffer/Sieve Motor—Manual Adjust
Clean Grain Elevator Belt—Adjusting
Clean Grain Elevator Belt—Replacing
Clean Grain Elevator Conveyor Chain—Adjusting
Tailings System Elevator Sensors
Tailings System Elevator Paddles
Tailings Elevator Drive Belt—Adjusting (S660 and S670)
Tailings System Elevator Paddle Chain—Adjusting
Upper Tailings Auger Drive Chain—Adjusting (S660 and S670)
Tailings System Drive Belt—Adjusting (S680 and S690)
Tailings System Drive Belt—Replacing (S680 and S690)
Tailings System Drive Chain—Adjusting (S680 and S690)
Tailings System Drive Chain—Replacing (S680 and S690)
Tailings System Wear Strips and Rasp Bars—Remove and Install
(S680 and S690)
Tailings System Wear Strips and Rasp Bars—Adjusting (S680
and S690)
Tailings System Return Concave—Adjusting (S680 and S690)
Tailings System Auger Cleanout Door (S680 and S690)
Drive Belts—Left-Hand
Drive Belts—Right-Hand (S660 and S670)
Drive Belts—Right-Hand (S680 and S690)
Feed Accelerator—Unplugging
Separator—Unplugging
Discharge Beater—Unplugging
Section 75 - Chopper and Spreader (Deluxe Residue)
Chopper (General Information)
Windrowing (General Information)
Chopper Tailboard—Adjusting
Chopper Vanes (Manual Adjust)—Adjusting
Chopper Vanes (Manual Adjust)—Factory Settings
PowerCast Tailboard—Adjusting (Optional)
PowerCast Tailboard Blade—Replacing (Optional)
PowerCast Tailboard (Optional) Rear Shrouds
Crop Diverter Vanes—Adjusting
Crop Diverter
Air Chutes
Chopper Access Door
Chopper Controller Bar (Optional)
Chopper Stationary Knifebank—Adjusting
Chopper Stationary Knife Blades—Replacing
Fine Cut Chopper Blades—Replacing and Configuration
Chopper Blades—Centering
Chopper Adjusting Switch
Chopper Drive Speeds—Changing
Chopper Drive Belt Tension—Adjusting
Chopper Belt—Replacing
Chopper Jackshaft Belt—Adjusting
Chopper Jackshaft Belt—Replacing (S660 and S670)
Chopper Jackshaft Belt—Replacing (S680 and S690)
Spreader (General Information)
Spreader—Windrow Position
Spreader—Lowering
Spreader Disks (Single Speed)—Replacing
Spreader Disks (Dual Speed)—Replacing
Wide Spread Straw Spreader (Optional)
Section 80 - Chopper and Spreader (Premium Residue)
Chopper (General Information)
Windrowing (General Information)
Crop Diverter Vanes—Adjusting
Crop Diverter
Air Chutes
Chopper Access Door
Overshot Beater Floor (If Equipped)—Removing
Chopper Controller Bar (Optional)
Chopper Stationary Knifebank—Adjusting
Chopper Stationary Knife Blades—Replacing
Middle Splitter Knife—Replacing
Fine Cut Chopper Blades—Replacing and Configuration
Chopper Blades—Centering
Chopper Adjusting Switch
Chopper Drive Speeds—Changing
Chopper Drive Belt Tension—Adjusting
Chopper Belt—Replacing
Chopper Jackshaft Belt—Adjusting
Chopper Jackshaft Belt—Replacing (S670)
Chopper Jackshaft Belt—Replacing (S680 and S690)
Advanced PowerCast Spreader Disks—Replacing
Windrow Convergence Rakes
Section 85 - Grain Tank and Unloading System
Grain Tank/Engine Ladder
Grain Tank Drain Holes
Grain Tank Sample Trough
Grain Tank Fill Sensors—Adjusting
Grain Tank Covers (If Equipped)—Operating
Grain Tank Covers (If Equipped)—Adjusting
Grain Tank Cross Auger Covers
Unloading Auger Drive Shear Bolt
Grain Tank Loading Auger Deflector
Grain Tank Loading Auger (Grain Tank Extensions)—Folding
Grain Tank Loading Auger (Grain Tank Covers)—Adjusting
Mass Flow Sensor Plate (Grain Tank Extensions)—Cleaning
Mass Flow Sensor Plate (Grain Tank Covers)—Cleaning
Unloading Auger Drive Chain—Adjusting
Unloading Auger Support Stud—Adjusting (78 L/sec. (2.2
bu./sec.) Unload Rate)
Unloading Auger Position—Adjusting (78 L/sec. (2.2 bu./sec.)
Unload Rate)
Unloading Auger Position—Adjusting (116 L/sec. (3.3 bu./sec.)
and 134 L/sec. (3.8 bu./sec.) Unload Rate)
Unloading Auger Cradle Support—Adjusting (116 L/sec. (3.3
bu./sec.) and 134 L/sec. (3.8 bu./sec.) Unload Rate)
Unloading Auger Drive Belt—Replacing
Section 90 - Service - Electrical System
Welding Near Electronic Control Units
Keep Electronic Control Unit Connectors Clean
Observe Electrical Precautions
Basic Electrical Component Handling / Precautions for Vehicles
Equipped with Computer Controlled Systems
Handling Batteries Safely
Batteries—Safe Installation
Battery Cables—Connecting
Batteries—Charging
Batteries—Checking Specific Gravity
Batteries—Connecting Booster
Batteries—Removing and Installing (S660 and S670)
Batteries—Removing and Installing (S680 and S690)
Battery Disconnect Switch
Fuse Center (S660 and S670)
Fuse Center (S680 and S690)
Chopper Fuses (If Equipped)
Safety Rules When Replacing Halogen Bulbs
Cab Headlight Bulb—Replacing
Cab Headlights—Adjusting
Cab Halogen Light Bulb—Replacing
Cab Halogen Lights—Adjusting
Fascia Light Bulb (If Equipped)—Replacing
Lower Driving Light Bulb (If Equipped)—Replacing
Lower Driving Light Bulb (If Equipped)—Adjusting
Safety Rules When Replacing High Intensity Discharge (HID) Xenon
Lights
High Intensity Discharge (Xenon) Light Bulb (Optional)—Replacing
High Intensity Discharge (Xenon) Lights (Optional)—Adjusting
Beacon Light Bulb—Replacing
Warning Lights, Road Lights, Field Lights—Replacing
Discharge Lights, Auxiliary Field Lights, Access Door Work Lights,
Stubble Lights, Grain Tank and Unloading Auger Light—Replacing
Side Finder Lights and Cleaning Shoe Lights—Replacing
Warning Lights—Replacing
Rear Hazard Lights and Marker/Brake Lights—Replacing
Cab Interior Light—Replacing
Map Light—Replacing
Section 95 - Diagnostic Trouble Codes
Accessing Diagnostic Trouble Code Menu
Diagnostic Trouble Code Priorities
Section 100 - Ground Drive and Rear Axle
Service Tires Safely
Tire Loading Decal
Care and Service of Tires
Front and Rear Tire Information
Drive Wheel Starter Stud
Drive Wheel Bolt Torque (Single Wheel Configuration)
Drive Wheel Bolt Torque (Dual Wheel Configuration)
Front Drive Wheel Offset
Preparing Dual Wheels for Transport or Service
Remove Front Wheels—Dual Wheels
Install Front Wheels—Dual Wheels
Single Attach Wide Spaced Dual Wheels (Optional)
Rear Wheel Bolt Torque
Using Liquid Weight
Ballast Requirements (S660)
Ballast Requirements (S670)
Ballast Requirements (S680)
Ballast Requirements (S690)
Jack Pocket Locations
Jack Pocket Location Decal
Section 105 - Break-In Service
Breaking-In Engine
Belt Drives Adjustment - First 50 Hours
Break-In Check First 100 Hours
Break-In Check After 100 Hours (Tier 2/Stage II)
Break-In Check After 375 Hours (Interim Tier 4/Stage III B)
Section 110 - Prestarting Checks
Engine Oil Level
Hydrostatic/Hydraulic Oil Level
Coolant Level
Fuel System
Fuel Tank Breather
Engine Air Scoop
Cleaning Engine Compartment
Section 115 - Operating the Engine
Exhaust Filter Cleaning
Exhaust Filter System Overview (Interim Tier 4/Stage III B)
When to Disable Exhaust Cleaning System
Exhaust Filter AUTO Mode (Interim Tier 4/Stage III B)
Parked Exhaust Filter Cleaning (Interim Tier 4/Stage III B)
Starting the Engine
Stopping the Engine
Handle Starting Fluid Safely
Cold Weather Starting Aid (If Equipped)
Coolant Heater
Section 120 - Service - Engine
Rear Ladder and Landing
Engine Filter Access Cover
Engine Access Covers
Changing Starting Fluid Can
Do Not Modify Engine Power or Fuel/Air System
Fuel System
Engine Oil Level
Fuel Tank—Filling
Fuel Tank—Draining
Fuel Tank—Shut-Off Valve
Water Separator Primary Fuel Filter—Draining
Fuel Precleaner Filter—Cleaning
Heavy Duty Fuel Precleaner Filter (Optional)—Flushing
Heavy Duty Fuel Precleaner Filter (Optional)
Primary and Secondary Fuel Filter Element—Replacing (Tier
2/Stage II) (S660 and S670)
Primary and Secondary Fuel Filter Element—Replacing (Tier
2/Stage II) (S680 and S690)
Primary and Secondary Fuel Filter Element—Replacing (Interim
Tier 4/Stage III B)
Fuel System—Bleeding
Cooling System—Draining
Cooling System—Filling
Cooling System—Winterize
Engine Belt—Routing (Tier 2/Stage II) (S660 and S670)
Engine Belt—Routing (Tier 2/Stage II) (S680 and S690)
Engine Accessory/Fan Drive Belt—Replacing (Tier 2/Stage
II) (S660 and S670)
Engine Accessory Belt—Replacing (Tier 2/Stage II) (S680
and S690)
Fan Drive Belt—Replacing (Tier 2/Stage II) (S680 and S690)
Rotary Screen Belt—Routing
Rotary Screen Drive Belt—Replacing (Tier 2/Stage II) (S660
and S670)
Rotary Screen Drive Belt—Replacing (Tier 2/Stage II) (S680
and S690)
Engine Belt—Routing (Interim Tier 4/Stage III B) (S660
and S670)
Engine Belt—Routing (Interim Tier 4/Stage III B) (S680
and S690)
Air Conditioner Compressor/Alternator Belt—Replacing (Interim
Tier 4/Stage III B) (S660 and S670)
Air Conditioner Compressor/Alternator Belt—Replacing (Interim
Tier 4/Stage III B) (S680 and S690)
Rotary Screen Drive Belt—Replacing (Interim Tier 4/Stage
III B) (S660 and S670)
Rotary Screen Drive Belt—Replacing (Interim Tier 4/Stage
III B) (S680 and S690)
Vacuum Fan Drive Belt—Replacing (Interim Tier 4/Stage
III B) (S660 and S670)
Vacuum Fan Drive Belt—Replacing (Interim Tier 4/Stage
III B) (S680 and S690)
Vacuum Fan Driven Belt—Replacing (Interim Tier 4/Stage
III B) (S660 and S670)
Variable Speed Fan Drive Belt—Replacing (Interim Tier
4/Stage III B) (S660 and S670)
Fan Drive Belt—Replacing (Interim Tier 4/Stage III B)
(S680 and S690)
Rotary Screen, Oil Cooler, Condenser, Radiator and Charge Air
Cooler—Cleaning
Rotary Screen Brush—Adjustment
Air Cleaner Filters—Removing
Diesel Particulate Filter Maintenance and Service (Interim Tier
4/Stage III B)
Exhaust Filter / Diesel Particulate Filter Ash Handling and
Disposal (Interim Tier 4/Stage III B)
Exhaust Filter Disposal (Interim Tier 4/Stage III B)
Section 125 - Transporting
Driving Machine on Roads
Back-Up Alarm
Transporting Machine on a Trailer
Machine Tie Down Location Decal
Towing Machine (Mechanical Shift Transmission Machines)
Towing Machine (Push Button Shift and ProDrive Transmission
Machines)
Front Tow Hook
Rear Tow Hook
Section 130 - Harvesting Hints
Harvesting Tips
Section 135 - Crop Settings
Alfalfa / Barley / Canola / Chickpeas / Corn (Dry) / Corn (Wet)
Corn Cob Mix / Edible Beans / Flax / Grass Seed / Guar (Cluster
Beans) / Lentils
Lupins / Millet / Mustard / Navy Beans / Oats / Peas
Popcorn / Rape Seed (Dry) / Rape Seed (Green) / Rice / Rye /
Safflower
Sorghum / Soybeans / Sunflower / Triticale / Wheat Difficult
/ Wheat Normal
Footnotes Description Page
Power Shutdown Procedure
Section 140 - Harvest Smart Feed Rate (Optional)
Harvest Smart Feed Rate—Operating Safely (If Equipped)
Harvest Smart Feed Rate—Description
Harvest Smart Feed Rate—Smart or Capacity Modes
Harvest Smart Feed Rate—Initial Calibration
Harvest Smart Feed Rate—Operation
Harvest Smart Feed Rate—Additional Information (Unloading
Auger ON and Field Conditions)
Harvest Smart Feed Rate—Best Practices
Harvest Smart Feed Rate—System Adjustments
Harvest Smart Feed Rate Control—System and Field Symptoms
Harvest Smart Feed Rate Troubleshooting
Harvest Smart Feed Rate Limp Mode and Emergency Modes
Section 145 - Fire Prevention
Recommended Fire Preventions
Fire Extinguisher Operation
Fire Extinguisher—Charging
Handle Fuel Safely—Avoid Fires
Prepare for Emergencies
Handle Starting Fluid Safely
Remove Accumulated Crop Debris
Fire Extinguisher
Fire Extinguisher Locations
In Case of Fire
Cleaning Engine Compartment
Section 150 - Machine Cleanout
General Cleaning Guidelines
Cleaning Out Machine (Periodic)
Cleaning Out Machine (Annual and Specialty Crops)
Section 155 - Fuels and Lubricants
Handle Fuel Safely—Avoid Fires
Fuel Tank—Filling
Handling and Storing Diesel Fuel
Diesel Fuel
Biodiesel Fuel
Lubricity of Diesel Fuel
Minimizing the Effect of Cold Weather on Diesel Engines
Heavy Duty Diesel Engine Coolant
Drain Intervals for Diesel Engine Coolant
John Deere COOL-GARD™ II Coolant Extender
Supplemental Coolant Additives
Operating in Warm Temperature Climates
Additional Information About Diesel Engine Coolants and John
Deere COOL-GARD™ II Coolant Extender
Testing Diesel Engine Coolant
Diesel Engine Break-In Oil (Tier 2/Stage II)
John Deere Break-In™ Plus Engine Oil (Interim Tier 4/Stage
III B)
Diesel Engine Oil (Tier 2/Stage II)
Diesel Engine Oil (Interim Tier 4/Stage III B)
Engine Oil and Filter Service Intervals (Tier 2/Stage II)
Engine Oil and Filter Service Intervals (Interim Tier 4/Stage
III B)
Oilscan™ and CoolScan™
Hydrostatic Drive System, Main Hydraulic System and Main Engine
Gearcase Oils
Transmission (Mechanical Shift and Push Button Shift), Final
Drives, Loading Auger, Primary Countershaft and Two-Speed Separator
Drive Gearcases
Feeder House Reverser Gearcase
Grease
Brake Fluid (If Equipped)
Oil Filters
Fuel Filters
Alternative and Synthetic Lubricants
Lubricant Storage
Mixing of Lubricants
Section 160 - Lubrication and Maintenance
Service Intervals—Clearing or Delaying
Lubrication Decal Locations
Hydraulic Hose Replacement
Hydraulic System Cleanliness
Lubrication Symbols
Every 10 Hours
Every 10 Hours
Every 50 Hours
Every 50 Hours
Every 50 Hours
Every 50 Hours
First 100 Hours (S670, S680 and S690 ProDrive Machines)
Every 200 Hours
Every 200 Hours (S660)
Every 250 Hours (Tier 2/Stage II) (S660 and S670)
Every 250 Hours (Tier 2/Stage II) (S680 and S690)
Every 250 Hours (Interim Tier 4/Stage III B) (S660 and S670)
Every 250 Hours (Interim Tier 4/Stage III B) (S680 and S690)
Every 400 Hours (S660 and S670)
Every 400 Hours (Tier 2/Stage II) (S680 and S690)
Every 400 Hours (Interim Tier 4/Stage III B) (S680 and S690)
Every 400 Hours (Interim Tier 4/Stage III B) (S660 and S670)
Every 400 Hours
Every 400 Hours
Every 400 Hours
Every 400 Hours
Every 400 Hours (S660 and S670 Non ProDrive Machines)
Every 400 Hours (S660 and S670 Push Button Shift Transmission
Machines)
Every 400 Hours (S670, S680 and S690 ProDrive Machines)
Every 400 Hours
Every 400 Hours
Every 800 Hours
Every 1000 Hours (S670 ProDrive Machines)
Every 1000 Hours (S680 and S690)
Every 1000 Hours (S680 and S690)
Every 2000 Hours (S660 and S670)
Every 2000 Hours (S680 and S690)
Every 2000 Hours
Every 2000 Hours or Six Years
As Required
4500 Hours or Five Years
Section 165 - Troubleshooting
Feeder House
Separator
Hydrostatic Ground Drive
Four-Wheel Drive (Optional)
Steering
Brakes
Engine
Electrical
Heater
Air Conditioner
Moisture Sensor (If Equipped)
Mass Flow Sensor (If Equipped)
Section 170 - Storage
Preparing Machine for Storage
Removing Machine From Storage
Section 175 - Specifications
Operating Speeds (S660 and S670)
Operating Speeds (S680 and S690)
Specifications (S660 and S670)
Specifications (S680 and S690)
Dimensions (S660)
Dimensions (S670)
Dimensions (S680 and S690)
Dimension Reference Points
Unified Inch Bolt and Screw Torque Values
Metric Bolt and Screw Torque Values
Section 180 - Machine Identification Numbers
Identification Numbers
Machine Identification Plate
Machine Identification Plate Location
Engine Serial Number (Tier 2/Stage II)
Engine Serial Number (Interim Tier 4/Stage III B)
Hydrostatic Drive Unit Pump
Hydrostatic Drive Unit Motor
Two Speed Four-Wheel Drive Motor
Engine Gearcase
Rotor Drive Gearcase
Transmission
Feeder House Reverser
Multi-Speed Feeder House Gearcase (If Equipped)
Chopper (If Equipped)
Chopper Tailboard (Deluxe Residue)
Chopper Tailboard (Premium Residue)
PowerCast Tailboard (Deluxe Residue)
Spreader (Deluxe Residue)
Keep Proof of Ownership
Keep Machines Secure
Section JDSLA - John Deere Service Literature Available
Technical Information
Section IBC - John Deere Service Keeps You On The Job
John Deere Is At Your Service